Golden Lighting 6390-5 WG User Manual
INSTALLATION INSTRUCTIONS
N
Fixture Name: CORONADA 6390-5 WG
For Pendant Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE（Fig.1）
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off the power at the circuit breaker and completely remove the old fixture
from the ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug, then thread into
Mounting Strap (D).
4. Place Lock Washer (B) and Hex Nut (A) over the end of Nipple (C) and
thread onto the nipple until tight.
5. Take this mounting strap assembly and mount to ceiling junction
box using Junction Box Screws (E). Tighten the screws securely with a screw
driver.
6. Unscrew Canopy Loop Collar (H) from the canopy loop. Pass
the canopy over the canopy loop leaving some threads exposed.
Adjust Nipple(C) until the desired height is reached. *the Canopy loop
collar should fit snugly. Remove the canopy and canopy lock collar.
7. Assemble the fixture and by measuring, determine the correct number
of links needed for proper hanging height. Use a pair of pliers to
open one link of chain to remove and discard the excess.
8. Use one Chain Connector (I) to attach one end of the chain to
Top Loop (J) and close the chain connector.
9. Feed the fixture wires through the chain (every three links) and pull
the wires until taut.
* Make sure the weight of the fixture will be supported by the
chain-not by the electrical wire.
10. Slip Canopy Loop Collar (H) over the chain, then do the same with
Canopy (G). Attach the chain to the Canopy Loop (F) with
Chain Connector (I).
11. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop (F) and nipple(C) into the outlet box.
Fig.1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
I
G
CONNECTING THE WIRES (Fig.2)
12. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or
RIBBED).
13. Attach the ground wire (GREEN or COPPER) from the junction
box and the fixture ground wire to the green ground screw on the
Mounting Bracket (B) or connect both wires together using the
correct size of wire connectors.
OTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
14. Tuck these wire connections neatly into the Junction Box.
15. Raise Canopy (G) to the ceiling and secure in place by tightening
the Canopy Loop Collar (H) into the Canopy Loop (F).
16. Install the light bulbs and glass shade as per the fixture assembly
sheet.
YOUR INSTALLATION IS NOW COMPLETE. TURN POWER ON AT
TO THE JUNCTION BOX & TEST THE FIXTURE.
Fig.2
FIXTURE WIRES
SMOOTH
(or Black)
RIBBED
(or White)
BARE COPPER
(or Green)
H
CHAIN
I
J
HOUSE WIRES
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
For Customer Service, contact the place of purchase to arrange for replacement parts.
C S A0 63 90 5D AL G 1
B
E
G
G
PARTS & ASSEMBLY SHEET
Fixture Name: CORONADA 6390-5 WG
This fixture assembled PO:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If
any parts are missing or damaged, please note on this sheet and contact the place of
purchase to arrange for replacement parts.
Company Name:______________________Co Account#:__________
PARTS LIST
below to be filled out by retailer
Date:
Canopy
1ea Φ140*H30 ㎜
Chain
1ea Φ3.8*6ft
Link
2ea W20*H45 ㎜
Loop
1ea W50*H70 ㎜
Hex Nut
2ea NPS-1/4-18
Nipple
1ea NPS 1/4-18*50
Mounting Strap
1ea W103*T2.0 ㎜
Cap
2ea Φ23*H5 ㎜
㎜
Wire Connectors
3ea Orange
Canopy Loop
1ea NPS 1/4-18*H41
Mounting Screws
2ea G8/32*H32 ㎜
Cover
2ea Φ42*H27 ㎜
㎜
Part Needed ______________________________ Quantity _________________________________
Part Needed ______________________________ Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
6390-5 WG
Fig.3
1. Thread nipple into the coupling and secure
with nut.
2. Place Cover (G), Tube (F), Column (E),
Cover (G) and Frame (D) over the nipple and
secure with nut.
3. Place Cap (B) over nipple and secure with
Loop (A).
4. Place Cap (B) over bottom nipple and
secure with Finial (C).
5. Install the bulbs as specified. (Bulbs are not
included)
(Do not exceed the maximum wattage rating!)
A
D
F
B
C
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTRUCITON SHEET FO R 6390-5WG-140521
Loading...