
PARTS & ASSEMBLY SHEET
NSTALL THE GLASS ASSEMBLY AFTER
Fixture Name: Hampden 6262-D5 DNI
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting Screws Top loop
1ea ∅5-1/2"*H1-1/4" 2ea 8#32-IP*1" 1ea 1/8-IP*H60mm
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Nipple Hex Nut Top cap
1ea 1/8-IP*H390mm 1ea 1/8-IP*H4mm 1ea ∅3-1/4"*H26mm
Cover Center column
1ea ∅2"*H5mm 1ea ∅2"*H387mm
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy loop
with Collar
Mounting strap
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
ASSEMBLING THE FIXTURE (Fig.1)
1. Gently spread the arms until evenly spaced if arms are
packed closed
2. Thread the Nipple (V) into Hickey(R), then tighten.
3. Slide the Center column (T) over the long Nipple (V) and
top with the Cover (S) and Top cap (M), tighten securely to
the Nipple using the washer (W) and the Hex Nut (U).
Fig 1
6262-D5 DNI
For Customer Service, contact the place of purchase to arrange for replacement parts.
6262-PartsInstallation_101110m.xls

4. Feed the fixture wires through the Top loop (J) and pull the
8. Feed the fixture wires through the Chain (every three links)
12. Place the Glass Shades(O) over the Threaded sockets(P),
PARTS & ASSEMBLY SHEET
Fixture Name: Hampden 6262-D5 DNI
ASSEMBLING THE FIXTURE (Fig.2)
wires until taut.
5. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
6. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.
7. Use one chain connector(E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.
and pull the wires until taut.
Fig 2
Fig 3
9. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy (F2).
10. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
canopy loop (A2) and close the chain connector.
11. Make sure the weight of the chandelier will be supported
by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
secure the Glass Shades (O) by threading by the
Socket Rings (N) until tight.
13. Install the light bulbs in accordance with the fixture's
specifications.
Fig 4
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
6262-PartsInstallation_101110m.xls

wire connector onto the wires.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
7. Unscrew the Canopy loop collar(H )from the Canopy loop. Take
desired height is reached. *the Canopy loop collar should fit snugly
INSTALLATION INSTRUCTIONS
Fixture Name:
Hampden 6262-D5, 6, 9, 3P DNI
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten screw securely with
screw driver.
For Chandelier Light Fixture
Fig. 1
the canopy and pass over the Canopy loop. approximatly one half
of the canopy loop exterior threads should be exposed. Adjust until
on the Canopy loop after the canopy is installed. Remove
Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9.Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires together
using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the
Fig. 2
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.