Golden Lighting 6262-BA4 DNI User Manual

Company Name:_______________________Co. Account #:_____

PARTS & ASSEMBLY SHEET

Read and review installation instruction sheet,

(DO NOT EXCEED MAXIMUM WATTAGE RATING!)

Fixture Name: Hampden 6262-BA4 DNI

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If

any parts are missing or damaged, please note onthis sheet and contact the place of
purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap Mounting Screws Deco Nut

1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 5/32-IP*H10mm

Wire connectors Mounting Screws Hex Nut

3ea P3 Orange 2ea 5/32-IP*1-3/4" 2ea 5/32-IP*H3mm

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

to be filled out by retailer

FIXTURE ASSEMBLY INSTRUCTIONS

but do not install before assembling the fixture.

Fig 1

6262-BA4 DNI

1. Slide the Glass Shade (J) over Socket ( I)
and secure Glass Shade (J) by threading the
Socket Ring (O) to Sock et (I) until tight.

2. Install the light bulb in accordance with the
fixture's specifications.

NOTE: INSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for rep lace ment p arts.

6262-BAPartsInstallation_20120313Rev.xls

INSTALLATION INSTRUCTIONS

6. Attach the power supply wires to the fixture lead wires

FINISHING THE INSTALLATION

Fig. 3

Fixture Name: Hampden 6262-BA4 DNI

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the car t on and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.

2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.

3. The Mounting Strap(F) contains several pairs of
threaded holes, find the pair of holes that m at c h t he
holes spacing in your fixture Back Plate(H) and thread
the two Mounting Screws(D) half way into the Mounting
Strap(F) and secure with Hex Nut (G).

4. Place the Mounting Strap(F)over the Junction Box
(A)so the Mounting Screws(D) are vertical or horizontal,
as required by fixture type.

5. Attach the Mounting Strap(F) to the Junct ion Box
using the two mounting screws(H)and tighten secur ely
with screw driver .

CONNECTING THE WI RES ( Fig 2)

by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHI TE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the
green Ground Screw (I) on the Mounting Bracket ( F) or
connect both wires together using the correct size of
wire connectors.
NOTE:Twist the wires together in the same direct ion you
twist the wire connector (L) onto the wires.

8. Tuck these wire connections neatly into the Junction
Box.

Fig. 1

Fig. 2

(Fig. 3)

9. After tucking these wire connections neat ly into the
Junction Box, place the fixture Back Plate(H) over the
two Mounting Screws (B).

10. Secure the Back Plate (H) against the wall by
threading two Deco Nuts (P) over the two Mounting
Screws (D) until tight as shown on Fig.1.

11. Install the light bulbs and glass shade as per the
fixture assembly sheet.
YOUR INSTALLATION I S NOW CO MPLET E. RETURN
POWE R TO THE JUNCTION BOX AND TEST THE
FIXTURE.

For Customer Service, contact t he place of purchase to arrange for replacement parts.