Page 1
Part Needed
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Rod
Read and review installation instruction sheet before
to be filled out by retailer
Company Name:_______________________Co. Account #:_____________
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
Fixture Name: Marco 6068-SF GMT
This fixture assembled PO:__________ Date: ________
Notice:
or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting Screws Mounting Strap
1ea ∅5"*H3/4" 2ea 8#32-IP*1"
Wire connectors Mounting Screws Hex Nut
3ea P3 Orange 2ea 5/32-IP*1-3/5" 2ea 5/32-IP*H3mm
Rod
3ea ∅11.7*H12" 1ea ∅11.7*H6" 2ea 5/32-IP*H10mm
Mounting Screws
2ea 5/32-IP*8MM
Part Needed Quantity
1ea ∅4"*H2mm
Deco Nut
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
1. By measuring determine correct number of rods needed
for proper hanging height.
* This fixture includes 4 rods (6", 12", 12", 12")
2. To shorten the fixture; slide the excess rods off the
wires. To lengthen add additional rods. The 12" rods are
optional.
3. Pull the fixture’s wires through the rods (G) until taut and
thread the rods together. Then thread to the fixture coupler
(W) at base of fixture and the swivel joint on Canopy. (F)
4. Insert the Steel wire rope (R) to hole at top of square
frame（T）and secure in place with Set Screws（S）until
tight.
5. Adjust the level of the frame (T) with the wire length.
Depress the cylinder lock at top cap to release wire.
6. Install the light bulbs in accordance with the fixture's
7. Place the Glass Shade (J) over the Socket (I).
specification.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
Fig 1
6068-SF GMT
For Customer Service, contact the place of purchase to arrange for replacement parts.
6068 Series Instructions_20111103m.xls
Page 2
INSTALLATION INSTRUCTIONS
Fig. 2
Fixture Name: Marco 6068-SF GMT
For Pendant Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Pen da nt (Fig. 1)
1. Carefully remove the new fixture from the car t on and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.
3. The Mounting bracket ( C ) contains several pairs of threaded
holes, find the pair of holes that match t he hole spacing in your
fixture Back Plate (N) and thread the two Mounting Screws (B)
half way into the Mounting Strap (C) facing down, these will
have their threaded ends protrude through the two holes in the
fixture canopy(N).
4. Place the Mounting Strap ( C ) over the junction box
5. Attach the Mounting Strap (C) to the Junct ion Box using the
two mounting screws (E). Tighten the scr ews ( E) s ecur ely with
screw driver.
CONNECTING THE WI RES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (E) or connect
both wires together using the correct size of wire
connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
FINISHING THE INSALLATION (Fig. 3)
9. Place the fixture’s canopy over the Mounting bracket
(C), adjust the canopy (N) until the Mounting Screws (B)
protrude out from the canopy (N) and secure by
threading the Decorative nuts (O) on until tight.
10. Install the light bulbs and glass shade as per the
fixture assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 3
For Customer Service, contact t he place of purchase to arrange for replacement parts.
Loading...