Golden Lighting 6068-M1L GMT User Manual

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Read and review installation instruction sheet before

Rod

PARTS & ASSEMBLY SHEET

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

Fixture Name: Marco 6068-M1L GMT

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing

or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Canopy Mounting screws Mounting strap

1ea ∅5"*H3/4" 2ea 8#32-IP*1"

Wire connectors Mounting screws Hex sut

3ea P3 Orange 2ea 5/32-IP*1-3/5" 2ea 5/32-IP*H3mm

Rod

3ea ∅11.7*H12" 1ea ∅11.7*H6" 2ea 5/32-IP*H10mm

Part Needed Quantity

1ea ∅4"*H2mm

Deco sut

FIXTURE ASSEMBLY INSTRUCTIONS

assembling the fixture.

1. By measuring determine correct number of rods
needed for proper hanging height.
* This fixture includes 4 rods (6", 12", 12", 12")

2. To shorten the fixture; slide the excess rods off the

Fig 1

6068-M1L GMT

wires. To lengthen add additional rods. The 12" rods are
optional.

3. Pull the fixture’s wires through the rods (G) until taut
and thread the rods together. Then thread to the fixture
coupler (H) at top of fixture and the swivel joint on
Canopy. (F)

4. Place the Glass Shade (J) over the Socket (I).

5. Install the light bulb in accordance with the fixture's
specification.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

6068 Series Instructions_20111103m.xls

)

fixture assembly sheet.

Fig. 3

INSTALLATION INSTRUCTIONS

Fixture Name: Marco 6068-M1L GMT

For Mini Pendant Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE as Pen da nt (Fig. 1)

1. Carefully remove the new fixture from the car t on and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.

3. The Mounting bracket ( C ) contains several pairs of
threaded holes, find the pair of holes that m at c h t he hole
spacing in your fixture Back Plate (N) and thread the two
Mounting Screws (B) half way into the Mounting Strap (C)
facing down, these will have their threaded ends protrude
through the two holes in the fixture canopy(N).

4. Place the Mounting Strap ( C ) over the junction box

5. Attach the Mounting Strap (C) to the Junct ion Box using
the two mounting screws (E). Tighten the s cr ews ( E) securely
with screw driver .

CONNECTING THE WI RES (Fig. 2)

6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and the fixture Ground wire to
the green Ground Screw on the Mounting Bracket (E)
or connect both wires together using the correct size of
wire connectors.
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction
Box.

Fig. 1

Fig. 2

FINISHING THE INSALLATION (Fig. 3

9. Place the fixture’s canopy over the Mounting bracket
(C), adjust the canopy (N) until the Mounting Screws
(B) protrude out from the canopy (N) and secure by
threading the Decorative nuts (O) on until tight.

10. Install the light bulbs and glass shade as per the

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.

For Customer Service, contact t he place of purchase to arrange for replacement parts.