Page 1
PARTS & ASSEMBLY SHEET
Notice:
Fig 1
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
Company Name:_______________________Co. Account #:____________
Fixture Name: Marco 6068-8 GMT
This fixture assembled PO:__________ Date: ________
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.
PARTS LIST
Canopy Mounting screws
1ea ∅5-1/4"*H20MM 2ea 8#32-IP*1" 1ea 1/8-IP*H62mm
Chain
1ea 6ft ∅4.2 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Mounting Screws
3ea 8#32-IP*8MM
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out by retailer
Top loop
Wire connectors Nipple
Canopy loop
with Collar
Mounting strap
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
ASSEMBLING THE FIXTURE (Fig. 1)
1. Thread the Center Column to connector (W) until
tight.
2. Insert the Steel wire rope (R) to hole at top of
square frame（T）and secure in place with Set
Screws（S）unti l tight.
3. Adjust the level of the frame (T) with the wire length.
Depress the cylinder lock at top cap to release wire.
For Customer Service, contact the place of purchase to arrange for replacement parts.
6068-8 GMT
Center
column
6068 Series Instructions_20111103m.xls
Page 2
Fig 3
PARTS & ASSEMBLY SHEET
Fixture Name: Marco 6068-8 GMT
3. Feed the fixture wires through the Top loop (J) and
pull the wires until taut.
4. Then screw the Top Loop (J) to the threaded center
column of Frame (M) until tight.
5. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers
to open one link of the Chain (C2) then remove the
excess Chain (C2) and discard it.
6. Use one chain connector(E2) to attach one end of
the chain to the Top loop (D2) and close the chain
connector.
Fig 2ASSEMBLING THE FIXTURE (Fig. 2)
7. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
8. Slip Canopy loop collar (B2) over the chain, then do
the same with the canopy (F2).
9. When ready to complete the installation Use the
other chain connector and attach the other end of the
chain to the canopy loop (A2) and close the chain
connector.
10. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture
is hung.
Fig 4
11. Install the light bulbs in accordance with the
fixture's
specifications.
12. Place the Glass shade (U) over the socket (V).
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
6068 Series Instructions_20111103m.xls
Page 3
INSTALLATION INSTRUCTIONS
7. Unscrew the Canopy loop collar (H ) from the Canopy
wiring connections.
CONNECTING THE WIRES (Fig 2)
Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
Fixture Name: Marco 6068-5/8 GMT
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the cart on and the
yellow bag that holds all parts. Check that all part s ar e
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and r emove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts ( A) ont o
Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Scr ews (E). Tighten screw
securely with screw driver.
loop. Take the canopy and pass over the Canopy loop.
approximatly one half of the canopy loop ext er ior t hr eads
should be exposed. Adjust until desired height is reached.
*the Canopy loop collar should fit snugly on the Canopy loop
after the canopy is installed. Remove Canopy and Canopy
lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete the
Fig. 1
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground w ire to the green Ground
Screw on the Mounting Bracket (D) or connect bot h wires
together using the correct size of wire connectors.
NOTE:
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar (H) into the Canopy Loop ( F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...