Golden Lighting 6068-1W GMT User Manual

Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing

Company Name:_______________________Co. Account #:_____________

Read and review installation instruction sheet, but

PARTS & ASSEMBLY SHEET

to be filled out by retailer

Fixture Name: Marco 6068-1W GMT

This fixture assembled PO:__________ Date: ________

Notice:

or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap Mounting screws

1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 5/32-IP*H9mm

Wire connectors Mounting screws Hex nut

3ea P3 Orange 2ea 5/32-IP*1-1/2"

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

Deco nut

2ea 5/32-IP*H3mm

FIXTURE ASSEMBLY INSTRUCTIONS

do not install before assembling the fixture.

Fig 1

6068-1W GMT

1. Slide the Glass (J) over the Socket (I )

2. Install the light bulb in accordance with the
fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase t o a rrange for replace ment p a rts.

6068 Series Instructions_20111103m.xls

3. The Mounting Strap (C) contains several pairs of threaded

4. Place the Mounting Strap (C) over the Junction Box so the

INSTALLATION INSTRUCTIONS

Fixture Name: Marco 6068-1W GMT

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

holes. Find the pair of holes that matches the holes spacing
in your fixture Back Plate (H). Thread the two Mounting
Screws (B) halfway into the Mounting Strap (C) and secure
with Hex Nut (D).

Mounting Screws (B) are horizontal or vertical as required by
the fixture.

5. Attach the Mounting Strap (C) to the Junction Box using
the two mounting screws (E). Tighten securely with
screwdriver.

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
NOTE: Twist the wires together in the same direction you
twist the wire connector (M) onto the wires.

7. Attach the GROUND wire (GREEN or COPPER) from the
junction box and the fixture ground wire to the green Ground
Screw (F) on the Mounting Bracket (C). Or, connect both
wires together using a wire connector.

8. Tuck these wire connections neatly into the junction box.

Fig. 1

Fig. 2

FINISHING THE INSTALLATION (Fig. 3)

9. After tucking these wire connections neatly into the
Junction Box, place the fixture Back Plate (H) over the two
Mounting Screws (B).

10. Secure the Back Plate (H) against the wall by threading
two Deco Nuts (P) over the two Mounting Screws (B) until
tight as shown on Fig.1.

11. Install the light bulb and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.

Fig. 3