Golden Lighting 6005-BA2 RBZ User Manual
Mounting
Strap
Junction Box
Screw
Mounting
Screw
1ea 4" X 3" 2ea 8/32" X 1" 2ea 5/32" X 28mm
Wire
Connnector
Hex Nut
Deco Nut
(round nut)
2ea P2 Orange 2ea 5/32" X 3.5mm 2ea 9 X 9.5mm
Green Ground
Screw
Socket Ring
(AB only)
Socket Ring
(PW, RBZ only)
1ea 8/32" X 10mm
2ea 51 x 23mm 2ea 50 x 9mm
Part Needed Quantity
Part Needed Quantity
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Fixture Name: Landcaster 6005-BA2 PW/RBZ/AB
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
or damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
For Customer Service, contact the place of purchase to arrange for replacement parts.
6005-BA2
Read and review installation instruction sheet
before assembling the fixture.
FIXTURE ASSEMBLY INSTRUCTIONS
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
1. Slide the Glass Shade (H) over Socket (I). Secure
Glass Shade (H) by threading the Socket Ring (J) on
to Socket (I) until tight.
Repeat for remaining glass shade.
2. Install light bulbs in accordance with fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
Fig. 1
K
I
L
H
J
6005-BA2PartsInstallation_111004m.xls Page 1
For Wall Mount Light Fixture
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fixture Name: Landcaster 6005-BA2 PW/RBZ/AB
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Fig. 1
Fig. 2
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3. The Mounting Strap (A) contains several pairs of threaded
holes. Find the pair of holes that match the hole spacing in your
fixture Back Plate (K). Thread the two Mounting Screws (B)
halfway into the Mounting Strap (A).
4. Place the Mounting Strap (A) over the Junction Box (E) so the
Mounting Screws (B) are horizontal.
5. Attach the Mounting Strap (A) to the Junction Box (E) by using
the two mounting screws (D). Tighten the screws securely.
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
7. Attach the GROUND wire (GREEN or COPPER) from the
junction box and the fixture ground wire to the green ground
screw on the Mounting Bracket (A). Or, connect both wires
together using a wire connector.
8. Tuck these wire connections neatly into the junction box.
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate (K), over the Mounting Screws
(B), so they protrude through the holes in the Back Plate (K).
10. Thread the Deco Nuts (L) onto the Mounting Screws (B) and
continue turning until the Back Plate (K) is snug against the wall.
11. Install glass according to the fixture assembly instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
JUNCTION BOX
E
A
G
F
D
B
C
K
I
L
H
HOUSE WIRES
WHITE
BLACK
RIBBED (WHITE)
SMOOTH (BLACK)
FIXTURE WIRES
Loading...