Golden Lighting 6005-1W RBZ User Manual
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Notice:
Company N ame:_______________________Co. Account #:_____________
below to be fille d out by r e ta iler
Read and review installation instruction sheet before
J
M
H
K
L
Fixture Name: Lancaster 6005-1W PW/RBZ/AB
This fixture ass embled PO:__________ Date: ________
Please review the parts listing and check for all parts before assem bling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap
1ea 3/4" X 4" 1ea 3/8 X 40mm 2ea 8/32 X 1"
Spring washer Hex nut Deco nut (round nut)
1ea 15 X 3mm 1ea 3/8 X 3mm 2ea 1 5 X 12mm
Green Ground
screw
1ea 8/32" X 10mm 3ea P2 Orange 1ea 50 X 9mm
Socket Ring
(AB only)
1ea 51 X 23mm
Part Needed Quantity
Part Needed Quantity
Threaded rod
(Nipple)
Wire connnector
Mounting screw
Socket Ring
(PW, RBZ only)
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
6005-1W
Fig. 1
1. Slide the Glass Shade (K) over S ocket (M). Secure
Glass Shade (K) b y threading the Socket R ing (L) onto
the Socket (M) until tight.
2. Install the light bulb in accordance with the fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!)
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
6005-1WPartsInstallation_111004m.xls Page 1
INSTALLATION INSTRUCTIONS
HOUSE WIRES
WHITE
BLACK
WHITE
BLACK
FIXTURE WIRES
WIRE CONNECTOR
J
M
H
K
L
FIXTURE WIRES
HOUSE WIRES
Fixture Name: Lancaster 6005-1W PW/RBZ/AB
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow bag that
holds all your part s. Check that al l parts are included as shown in the
illustration and parts list.
2. Shut off power at the circuit breaker and remove the old fixture from
wall, including the old mounting str ap.
3. Take Threaded Rod (D) f rom parts bag and thread into center screw
hole on Mounting Strap (A). Tighten with Hex Nut (B ) and Spring W asher
(C).
4. Attach the Mounting Strap (A) to the Junction Box (I) us ing the two
Mounting Screws (E). Tighten the screws securely.
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
NOTE: Twist the wires together in the same direction you twist the
wire connector onto the wires.
Fig. 1
Fig. 2
6. Attach the GROUND wire (GREEN or COPPER) from the
junction box and the fixture ground wire to the green ground screw
on the Mounting Bracket (A). Or connect both wires together
using a wire connector.
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
8. Place the fixture Back Plate (J) over the Threaded Rod (D), so
it protrudes through the hole in the Back Plate (J).
9. Thread the Deco Nut (H) onto the Threaded Rod (D) and
continue turning until the Back Plate (J) is snug against the wall.
10. Install glass according to the fixture assembly instructions.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER
TO THE JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...