Golden Lighting 6005-13 RBZ User Manual

Part Needed

Quantity

Reason why

( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS & ASSEMBLY SHEET

NOTE: I

L

Fixture Name: Lancaster 6005-13 PW/RBZ

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

Company Name:_______________________Co. Account #:_____________

PARTS LIST

Mounting strap Junction box screws Wire connectors

1ea 4"*H1.5mm 2ea #8-32N*18mm 2ea P3 Orange

Green ground screw Mounting Screws Hex Nut

1ea #8-32N*10mm 2ea 5/32"*H40mm 2ea 5/32-IP*H3.5mm

Deco nut Nipple

2ea 5/32"*H9mm 1ea 3/8-IP*H80~95mm

to be filled out by retailer

Hex Nut

2ea 3/8"*H3mm 1ea Ø62*H20mm 1ea Ø14*H13mm

Part Needed Quantity

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet before
assembling the fixture.

1. Thread the Nipple (H) into the Ceiling pan coupler (F)
and secure with Hex nut attached.

2. Install the light bulbs in accordance with the fixture's
specifications.

3. Place the Glass shade (I) over the Ceiling pan (E)
allowing the Nipple (H) to protrude through the bottom
hole in the glass tighten with Hex Nut (J), slide Bottom
cap (K) over Nipple (H) and tighten with Finial (L)

Bottom cap Finial

6005-13 PW/RBZ

Fig 1

E

F
G

H

(DO NOT EXCEED MAXIMUM WATTAGE RATING!)

NSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

6005-13PartsInstallation_20100930m.xls

I

J

K

INSTALLATION INSTRUCTIONS

Fixture Name: Lancaster 6005-13 PW/RBZ

For Flush Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.

2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.

3. The Mounting strap (B) contains several pairs of
threaded holes, find the pair of holes that match the holes
spacing in your Canopy (E) and thread the two Mounting
screws (A) into the Mounting strap (B), secure with Hex
nuts (D).

4. Place the Mounting strap (B) over the Junction box so
the Mounting screws (A) are vertical or horizontal, as
required by fixture type.

5. Attach the Mounting strap (B) to the Junction box by
using the two Mounting screws (C). Tighten the screws
securely with screw driver!!

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires

by connecting BLACK to BLACK (or SMOOTH) and

WHITE to WHITE (or RIBBED).

7. Attach the ground wire (GREEN or COPPER) from the

Junction Box and the fixture ground wire to the green

Ground screw on the Mounting strap (B) or connect both

wires together using the correct size of wire connectors.

NOTE: Twist the wires together in the same direction you

twist the wire connector onto the wires.

8. TucK these wire connections neatly into the Junction

Box.

Fig. 1

Fig. 2

FIXTURE WIRES

SMOOTH ( or BLACK)

RIBBED ( or WHITE)

BARE COPPER

A

B
C

D

HOUSE WIRES

BLACK
(Hot)

WHITE
(Netural)

GREEN
(Ground)

E

F
G

FINISHING THE INSTALLATION (Fig. 3)

9. Raise the Ceiling pan (E) against the ceiling and tighten

with Deco nuts (G).

10. Install the light bulbs in accordance with the fixture's

specifications and install the glass assembly as per

Assembly instructions.

YOUR INSTALLATION IS NOW COMPLETE, RETURN

POWER TO THE JUNCTION BOX AND TEST THE

FIXTURE.

Fig. 3

For Customer Service, contact the place of purchase to arrange for replacement parts.

A

B
C

D

E

F
G