Golden Lighting 5222-4 RBZ-TEA User Manual
PARTS & ASSEMBLY SHEET
_
Fixture Name:
Notice:
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
PARTS LIST
Mounting
Strap
Spring Washer 1ea Hex Nut 1ea
Green Ground
Screw
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Please review the parts listing and check for all parts before assembling the fixture. If any
Company Name:_______________________Co. Account #:________
to be filled out by retailer
1ea
1ea
Threaded Rod
(Nipple)
Wire
Connnector
CENTENNIAL 5222-4 PW,CH,ORB and 5664 RBZ
This fixture assembled PO:__________ Date: ________
1ea
2ea
Mounting
Screw
Deco Nut
(round nut)
2ea
1ea
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
1.Place the Glass Shade(K)over the Socket (M).
2.Holding the Glass Shade(K), place the Socket
Ring(L)over the Threaded Socket(M).
3. Secure Glass Shade(K) by threading the Socket
Ring(L) onto the Threaded Socket(M) until tight.
4.Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE
RATING!)
Fig 4
5222-4 and 5664
J
H
M
K
L
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: CENTENNIAL 5222-4 PW,CH,ORB and 5664 RBZ
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3. Thread the Nipple (D) into the Mounting Strap (A). Place
Lock Washer (C) over end of Nipple (D) protruding through
Mounting Strap (A) and thread Hex Nuts (B) onto Nipple
until tight.
4. The Mounting Strap(A) contains several pairs of
threaded holes, find the pair of holes that match the holes
spacing in your fixture Back Plate(D) and thread the two
Mounting Screws(E) half way into the Mounting Strap(A).
5. Place the Mounting Strap(A)over the Junction Box so
the Mounting Screws(E) are vertical or horizontal, as
required by fixture type and fasten using the two mounting
screws (B). Tighten the screws (B) securely with screw
driver.
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect
both wires together using the correct size of wire
connectors.
NOTE:Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
FINISHING THE INSTALLATION (Fig.3)
9. Place the fixture Back Plate ( J ), over the threaded rod,
so it protrudes through the hole in the Back Plate ( J ).
Thread the Deco Nut ( H ) onto the threaded rod and
continue turning until the Back Plate(J) is snug against the
wall.
10. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 3
J
H
For Customer Service, contact the place of purchase to arrange for replacement parts.
M
K
L
Loading...