Golden Lighting 5222-2 RBZ-TEA User Manual
_
PARTS & ASSEMBLY SHEET
Fixture Name: CENTENNIAL 5222-2 PW,CH,ORB and 5662 RBZ
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
Company Name:_______________________Co. Account #:________
PARTS LIST
to be filled out by retailer
Mounting
Strap
Spring Washer 1ea Hex Nut 1ea
Green Ground
Screw
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
1ea
1ea
Threaded Rod
(Nipple)
Wire
Connnector
1ea
2ea
Mounting
Screw
Deco Nut
(round nut)
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
Fig 4
5222-2 and 5662
2ea
1ea
1.Place the Glass Shade(K)over the Socket (M).
2.Holding the Glass Shade(K), place the Socket
Ring(L)over the Threaded Socket(M).
3. Secure Glass Shade(K) by threading the Socket
Ring(L) onto the Threaded Socket(M) until tight.
4.Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE
RATING!)
J
H
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
M
K
L
INSTALLATION INSTRUCTIONS
Fixture Name: CENTENNIAL 5222-2 PW,CH,ORB and 5662 RBZ
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3. Thread the Nipple (D) into the Mounting Strap (A). Place
Lock Washer (C) over end of Nipple (D) protruding through
Mounting Strap (A) and thread Hex Nuts (B) onto Nipple until
tight.
4. The Mounting Strap(A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture Back Plate(D) and thread the two Mounting
Screws(E) half way into the Mounting Strap(A).
5. Place the Mounting Strap(A)over the Junction Box so the
Mounting Screws(E) are vertical or horizontal, as required by
fixture type and fasten using the two mounting screws (B).
Tighten the screws (B) securely with screw driver.
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect both
wires together using the correct size of wire connectors. -
NOTE:Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
Fig. 1
Fig. 2
FINISHING THE INSTALLATION(Fig.3)
9. Place the fixture Back Plate ( J ), over the threaded rod,
so it protrudes through the hole in the Back Plate ( J ).
Thread the Deco Nut ( H ) onto the threaded rod and
continue turning until the Back Plate(J) is snug against the
wall.
10. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Fig. 3
J
H
For Customer Service, contact the place of purchase to arrange for replacement parts.
M
K
L
Loading...