Golden Lighting 5221-5 RBZ-TEA User Manual
_
PARTS & ASSEMBLY SHEET
Fixture Name:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
PARTS LIST
Anchor 2ea
Anchor Screw 2ea
Green Ground
Screw
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
1ea
Company Name:_______________________Co. Account #:________
to be filled out by retailer
Junction Box
Screw
Wire
Connnector
Deco Nut
(round nut)
Brookfield 5221-5 CH, ORB, PW and 5335 RBZ
This fixture assembled PO:__________ Date: ________
2ea
2ea
2ea
Mounting
Plate
1 ea
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
1.Slide the Glass Shade ( H ) over Socket(G)
and secure Glass Shade (H) by threading the
Socket Ring(I) to Socket (G) until tight.
2. Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
5221-5 and 5334
Fig 1
F
G
H
J
I
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
)
Fixture Name: Brookfield 5221-5 CH, ORB, PW and 5335 RBZ
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE(Fig.1)
1.Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.
3. Hold Mounting Plate(B) up against the wall aligning
the two holes in the Junction Box with appropriate slots
in the Mounting Plate(B). Then while the Mounting
Plate(B) is leveled horizontally, use a pen or pencil to
make a mark on the wall at holes located near each
end of mounting Plate(B). Set aside the Mounting
Plate(B) and insert Wall Anchors (A) into the two
marks made on the wall.
4. Thread the supply wires and ground wire from
Junction Box through center holes in Mounting
Plate(B).
5. Attached the Mounting Plate(B) to Junction Box by
using the two Junction Box Screws(E). If Anchors (A)
were attached to the wall, secure the Mounting Plate (B
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and the fixture Ground wire to
the green Ground Screw on the Mounting Plate (B) or
connect both wires together using the correct size of
wire connectors.
NOTE:Twist the wires together in the same direction
you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSTALLATION(Fig.3)
9. After tucking these wire connections neatly into the
Junction Box and place the fixture Front Plate(F) over
the two Mounting Screws(D) and secure against the
Mounting Plate by threading two Deco Nuts(J) over the
two Mounting Screws(D) until snug against the wall.
10. Install the light bulbs and glass shade as per the
fixture assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Fig. 1
A
Fig. 2
Fig. 3
B
C
E
D
B
A
F
D
G
H
J
I
C
E
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...