Golden Lighting 5221-2 RBZ-TEA User Manual
_
PARTS & ASSEMBLY SHEET
Fixture Name: Brookfield 5221-2 CH , ORB, PW and 5332 RBZ
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any
parts are missing or damaged, please note onthis sheet and contact the place of purchase to
arrange for replacement parts.
Company Name:_______________________Co. Account #:________
PARTS LIST
to be filled out by retailer
Mounting
Strap
Spring Washer 1ea Hex Nut 1ea
Green Ground
Screw
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
1ea
1ea
Threaded Rod
(Nipple)
Wire
Connnector
1ea
2ea
Mounting
Screw
Deco Nut
(round nut)
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
Fig 1
5221-2 and 5332 RBZ
2ea
1ea
M
1.Place the Glass Shade(K)over the Socket (M).
2.Holding the Glass Shade(K), place the Socket
Ring(L)over the Threaded Socket(M).
3. Secure Glass Shade(K) by threading the Socket
Ring(L) onto the Threaded Socket(M) until tight.
4.Install the light bulb in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE
RATING!)
H
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
J
K
L
INSTALLATION INSTRUCTIONS
Fixture Name: Brookfield 5221-2 CH , ORB, PW and 5332 RBZ
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE(Fig.1)
1. Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.
3. Thread the Nipple (D) into the Mounting Strap (A).
Place Lock Washer (C) over end of Nipple (D)
protruding through Mounting Strap (A) and thread Hex
Nuts (B) onto Nipple until tight.
4. The Mounting Strap(A) contains several pairs of
threaded holes, find the pair of holes that match the
holes spacing in your fixture Back Plate(J) and thread
the two Mounting Screws(E) half way into the Mounting
Strap(A).
5. Place the Mounting Strap(A)over the Junction Box
so the Mounting Screws(E) are vertical or horizontal, as
required by fixture type and fasten using the two
mounting screws (B). Tighten the screws (B) securely
with screw driver.
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and the fixture Ground wire to
the green Ground Screw on the Mounting Bracket (A)
or connect both wires together using the correct size of
wire connectors. -
NOTE:Twist the wires together in the same direction
you twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
FINISHING THE INSTALLATION(Fig.3)
9. Place the fixture Back Plate ( J ), over the threaded
rod, so it protrudes through the hole in the Back Plate
(J). Thread the Deco Nut ( H ) onto the threaded rod
and continue turning until the Back Plate(J) is snug
against the wall.
10. Install the light bulbs and glass shade as per the
fixture assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Fig. 3
H
M
J
K
L
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...