Page 1
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
Fixture Name: Nelio 4444-BA4 PW
This fixture assembled PO:__________ Date: ________
Notice:
are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
Please review the parts listing and check for all parts before assembling the fixture. If any parts
PARTS LIST
Mounting Strap
1ea 4"X3" 2ea 8/32"X1" 2ea 5/32"*H30mm
Wire
Connnector
3ea P3 Orange 2ea 5/32"X3.5mm 2ea 5/32"*H9mm
Green Ground
Screw
1ea 8/32"X10mm
Part Needed Quantity
Part Needed Quantity
Junction Box
Screw
Hex Nut
Mounting
Screw
Deco Nut
(round nut)
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
Fig. 1
1. Slide the Fitter (I) and Glass Shade (H) over Socket
(L) and secure Glass Shade (H) by threading the
Socket Ring (J) to Socket (L)
2. Install light bulb in accordance with fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NOTE: I
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
NSTALL THE GLASS ASSEMBLY
4444-BA4 PW
M
K
J
H
I
L
4444-BAPartsInstallation_101112m.xls
Page 2
INSTALLATION INSTRUCTIONS
2. Shut off power at the circuit breaker and remove the old fixture
11. Install glass as per the fixture assembly instructions
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER
Fixture Name:
Nelio 4444-BA4 PW
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.
from wall, including the old mounting strap.
3. The Mounting Strap(A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in your
fixture Back Plate (K) and thread the two Mounting Screws(B)
half way into the Mounting Strap(A).
4. Place the Mounting Strap (A) over the Junction Box (E) so the
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.
5. Attach the Mounting Strap (A) to the Junction Box (E) by using
the two mounting screws(D). Tighten the screws securly.
For Wall Mount Light Fixture
Fig. 1
JUNCTION BOX
E
B
G
C
A
F
D
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (A) or connect both wires
together using the correct size of wire connectors.
NOTE:Twist the wires together in the same direction you twist
the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate (K), over the Mounting screws(B),
so they protrude through the holes in the Back Plate (K).
10. Thread the Deco Nuts (M) onto the Mounting Screws (B) and
continue turning until the Back Plate (K) is snug against the wall.
Fig. 2
FIXTURE WIRES
SMOOTH (BLACK)
Fig. 3
RIBBED (WHITE)
M
K
HOUSE WIRES
BLACK
WHITE
J
H
I
L
TO THE JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...