Golden Lighting 4444-BA3 PW User Manual

Reason why

( missing, scratched, broken glass, bent, bad finish)

Comments

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

PARTS & ASSEMBLY SHEET

Fixture Name: Nelio 4444-BA3 PW

This fixture assembled PO:__________ Date: ________

Notice:

are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.

Please review the parts listing and check for all parts before assembling the fixture. If any parts

PARTS LIST

Mounting Strap

1ea 4"X3" 2ea 8/32"X1" 2ea 5/32"*H30mm

Wire
Connnector

3ea P3 Orange 2ea 5/32"X3.5mm 2ea 5/32"*H9mm

Green Ground
Screw

1ea 8/32"X10mm

Part Needed Quantity

Part Needed Quantity

Junction Box
Screw

Hex Nut

Mounting
Screw

Deco Nut
(round nut)

F

IXTURE ASSEMBLY INSTRUCTIONS

Read and review installation instruction sheet
before assembling the fixture.

Fig. 1

1. Slide the Fitter (I) and Glass Shade (H) over Socket
(L) and secure Glass Shade (H) by threading the
Socket Ring (J) to Socket (L)

2. Install light bulb in accordance with fixture's
specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

4444-BA3 PW

K

H

M

I

L

NOTE: I

AFTER THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

NSTALL THE GLASS ASSEMBLY

J

4444-BAPartsInstallation_101112m.xls

2. Shut off power at the circuit breaker and remove the old fixture

11. Install glass as per the fixture assembly instructions

YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER

INSTALLATION INSTRUCTIONS

J

Fixture Name: Nelio 4444-BA3 PW

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and the

yellow bag that holes all your parts. Check that all parts are

included as shown in the illustration and parts list.

from wall, including the old mounting strap.

3. The Mounting Strap(A) contains several pairs of threaded

holes, find the pair of holes that match the holes spacing in your

fixture Back Plate (K) and thread the two Mounting Screws(B)

half way into the Mounting Strap(A).

4. Place the Mounting Strap (A) over the Junction Box (E) so the

Mounting Screws (B) are vertical or horizontal, as required by

fixture type.

5. Attach the Mounting Strap (A) to the Junction Box (E) by using

the two mounting screws(D). Tighten the screws securly.

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires by

connecting BLACK to BLACK (or SMOOTH) and WHITE to

WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from the

Junction Box and the fixture Ground wire to the green Ground

Screw on the Mounting Bracket (A) or connect both wires

together using the correct size of wire connectors.

NOTE:Twist the wires together in the same direction you twist

the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

JUNCTION BOX

E

G

Fig. 2

FIXTURE WIRES

SMOOTH (BLACK)

B

RIBBED (WHITE)

A

C

HOUSE WIRES

BLACK

F

D

WHITE

FINISHING THE INSTALLATION (Fig.3)

9. Place the fixture Back Plate (K), over the Mounting screws(B),

so they protrude through the holes in the Back Plate (K).

10. Thread the Deco Nuts (M) onto the Mounting Screws (B) and

Fig. 3

H

continue turning until the Back Plate (K) is snug against the wall.

K

M

I

L

TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.