Page 1
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
below to be filled out by retailer
L
Fixture Name: Nelio 4444-BA1 PW
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
PARTS LIST
Mounting strap Junction box screw Threaded rod
1ea 3/4"X4" 2ea #8-32N*H25mm 1ea @3/8X45MM
Wire
connnector
2ea P3 Orange 1ea @3/8X3mm 1 ea 3/8"*H12mm
Green ground
screw
1ea 8/32"X10mm 1 ea Ø15*H3mm
Part Needed Quantity
Part Needed Quantity
Hex nut
Spring washer
Deco nut
(Round)
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Slide the Fitter (I) and Glass shade ( H ) over Socket
(L) and secure Glass Shade (H) by threading the
Socket Ring (J) onto the Socket (L) until tight.
2. Install the light bulb in accordance with the fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NOTE: I
THE FIXTURE IS HUNG.
NSTALL THE GLASS ASSEMBLY AFTER
Fig. 1
K
4444-BA1 PW
J
H
I
M
For Customer Service, contact the place of purchase to arrange for replacement parts.
4444-BAPartsInstallation_101112m.xls
Page 2
INSTALLATION INSTRUCTIONS
L
G
F
D
E
1.Carefully remove the new fixture from the carton and the
2. Shut off power at the circuit breaker and remove the old
center screw hole on Mounting Strap (A), tighten with Hex
NOTE: Twist the wires together in the same direction you
Fixture Name: Nelio 4444-BA1 PW
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
yellow bag that holds all your parts. Check that all parts
are included as shown in the illustration and parts list.
fixture from wall, including the old mounting strap.
3.Take Threaded Rod (D) from parts bag and thread into
Nut (B) and Spring Washer (C).
4. Attach the Mounting Strap (A) to the Junction Box (I)
using the two Mounting Screws (E). Tighten the screws
securely.
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
6. Attached the GROUND wire (GREEN or COPPER)
from the Junction Box and the fixture Ground wire to the
green Ground Screw on the Mounting Strap (B) or
connect both wires together using the correct size of wire
connectors
Fig. 1
JUNCTION BOX
I
Fig. 2
FIXTURE WIRES
SMOOTH (BLACK)
C
B
A
D
N
G
HOUSE WIRES
BLACK
WHITE
twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSTALLATION (Fig. 3)
8. Place the fixture Back Plate (K) over the Thread Rod
(D),so it protrudes through the hole in the Back Plate (K).
9. Thread the Deco Nut (M) onto the Threaded Rod (D)
and continue turning until the Back Plate (K) is snug
against the wall.
10. Install glass as per the fixture assembly instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
K
RIBBED (WHITE)
J
H
I
M
Loading...