Page 1
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
NOTE: I
1. Pull the wires up and slide the center column (A)
curve into the top loop facing out and then the wide
Fig 3
Read and review installation instruction sheet
before assembling the fixture.
PARTS & ASSEMBLY SHEET
PARTS LIST
Company Name:_______________________Co. Account #:________
to be filled out by retailer
G
F
C
D
E
A
B
Fixture Name: Loretto 4002-9 RSB
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If
any parts are missing or damaged, please note onthis sheet and contact the place of purchase
to arrange for replacement parts.
Canopy 1ea
Chain 6ft
Chain
connector
Mounting
Strap
Part Needed Quantity
2ea Canopy Loop 1ea Bottom Cap 1ea
1ea Hex Nut 2ea Finial 1ea
Mounting
Screws
Wire
Connectors
2ea
3ea
Nipple
(70mm)
Nipple
(30mm)
FIXTURE ASSEMBLY INSTRUCTIONS
4002-9 RSB
into the center of main frame. There is no
1ea
1ea
threading, there is no coupler.
2. Then hang decorative arms(3ea) (B) onto the
center column (A) and frame. Tuck the narrow S
S curve will slide into the loop at the bottom of
frame. These arms will support the weight of the
fixture, not the center column.
NSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact t he place of purchase to arrange for replacement parts.
Page 2
10. Thread nipple (70mm)(C) into the coupling and
included in the package).
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
Fig 5
PARTS & ASSEMBLY SHEET
3. Feed the fixture wires through the Top loop
7. Slip Canopy loop collar (B2) over the chain, then
Fig 4
B2
A2
C2
E2
Fixture Name: Loretto 4002-9 RSB
(D2) and pull the wires until taut. Then screw
the Top Loop（D2） to the coupling on the top of
fixture (A) until tight.
4. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
5. Use one chain connector(E2) to attach one end
of the chain to the Top loop (D2) and close the
chain connector.
6. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
do the same with the canopy (F2).
8. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
9. Feed the fixture wires through canopy loop (F)
and nipple(C) and pull until taut.
E2
D2
secure with nut.
11. Place the Bottom Cap (D) over the nipple (C)
and secure with finial (E).
12. Place Glass Shade (F) over the socket and
secure with Socket Ring (G).
13. Install the bulbs as specified. (no bulbs
For Customer Service, contact t he place of purchase to arrange for replacement parts.
Page 3
HANGING THE FIXTURE (Fig.1)
attached into Mounting Strap (D).
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
securely with screw driver.
CONNECTING THE WIRES (Fig 2 )
FINISHING THE INSTALLATION (Fig.3)
tightening the Canopy loop collar(H) into the Canopy Loop(F)
assembly sheet.
7. Unscrew the Canopy loop collar(H)from the Canopy loop.
installed. Remove Canopy and Canopy lock collar.
outlet box.
INSTALLATION INSTRUCTIONS
YOUR INSTALLATION IS NOW
Fig. 1
Fig. 2
JUNC TIO N BOX
(CEILING )
A
B
D
C
E
F
I
I
G
H
CHAIN
J
Fixture Name: Loretto 4002-9 RSB
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
5. Place Lock Washer (B) over end of Nipple (C) protruding
until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw
For Chandelier Light Fixture
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
should fit snugly on the Canopy loop after the canopy is
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop(F) and nipple(C) and into the
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both wires
together using the correct size of wire connectors. - NOTE:
Twist the wires together in the same direction you twist the wire
connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
14. Install the light bulbs and glass shade as per the fixture
COMPLETE. RETURN POWER TO THE
JUNCTION BOX AND TEST THE
FIXTURE.
Page 4
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...