Golden Lighting 3711-WSC CB User Manual
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
Company Name:_______________________Co. Account #:_____________
PARTS & ASSEMBLY SHEET
Fixture Name: Rockefeller 2488-WSC FI & 3711-WSC CB
This fixture assembled PO:__________ Date: ________
Notice:
or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting Strap Mounting Screws Metal Cap Nut
1ea 4-1/8-IP*H2mm 2ea 8#32-IP*1" 1ea 1/8-27-IP*H15mm
Wire connectors Nipple Hex Nut
3ea P3 Orange 1ea 1/8-27-IP*1-3/4"
Nipple (17)
*may have washers,
hex nuts attached
1ea 1/8-27-IP*2-1/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet, but
do not install before assembling the fixture.
to be filled out by retailer
Bottom Cap
1ea ∅2-1/2"*H1-1/2"
3ea 1/8-27-IP*H3mm
Finial
1ea 1/8-27-IP*H27mm
2488-WSC FI & 3711-WSC CB
1. Thread on the nipple (17) in this order:hex nut,
Fig 1
metal washer (18), plastic washer (19), glass
shade (16) thread the nipple through the hole in
bottom of glass shade, plastic washer, metal
washer, hexnut (20) ,bottom cap (21) and secure
in place with the Finial (22).
2. Place the glass shade (16) into the fixture frame
(15), level the glass.
3. Install the light bulb in accordance with the
fixture's specifications.
NOTE: I
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
(D) and continue turning until the Back Plate (15) is snug
INSTALLATION INSTRUCTIONS
G
F
D
E
Fixture Name: Rockefeller 2488-WSC FI &3711-WSC CB
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.
3. Take Threaded Rod (D) from parts bag and thread
into center screw hole on Mounting Strap (A), tighten
with Hex Nut (B) and Spring Washer (C).
4. Attach the Mounting Strap (A) to the Junction Box (I)
using the two Mounting Screws (E). Tighten the screws
securely.
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
6. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the
green Ground Screw on the Mounting Bracket (A) or
connect both wires together using the correct size of
wire connectors.
NOTE:Twist the wires together in the same direction you
twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
JUNCTION BOX
A
B
I
C
D
N
G
FINISHING THE INSTALLATION (Fig. 3)
8. Place the fixture Back Plate (14) over the Threaded
Rod (D), so it protrudes through the hole in the Back
Plate (15).
9. Thread the Metal Cap Nut (6) onto the Threaded Rod
against the wall.
10. Install glass as per the fixture assembly instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...