Golden Lighting 3711-BA3 CB User Manual

Read and review installation instruction sheet, but

PARTS & ASSEMBLY SHEET

Company Name:_______________________Co. Account #:________

Fixture Name: Rockefeller 2488-BA3 FI & 3711-BA3 CB

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are

missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.

PARTS LIST

Mounting Strap Mounting Screws Deco Nut

1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 5/32-IP*H9mm

Wire connectors Mounting Screws Hex Nut

3ea P3 Orange 2ea 5/32-IP*1-1/4"

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

to be filled out by retailer

2ea 5/32-IP*H3mm

FIXTURE ASSEMBLY INSTRUCTIONS

do not install before assembling the fixture.

2488-BA3 FI & 3711-BA3 CB

1. Slide the Glass Shade (J) over Socket ( I) and
secure Glass Shade (J) by threading the Sock et
Ring (O) to Socket (I) until tight.

2. Thread the final cap (R) into t he square tube
(S) unitl tigh t.

3. Install the light bulb in accordance with the
fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for rep lace ment p arts.

24883711-PartsInstallation_20120411m.xls

Fig 1

(A)so the Mounting Screws (D) are vertical or horizontal,
NOTE:Twist the wires together in the same direction you

FINISHING THE INSTALLATION

Fig. 3

Fig. 2

INSTALLATION INSTRUCTIONS

Fixture Name: Rockefeller 2488-BA3 FI & 3711-BA3 CB

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and
the yellow bag that holes all your parts. Check that all
parts are included as shown in the illustration and parts
list.

2. Shut off power at the circuit breaker and remove the
old fixture from wall, including the old mounting strap.

3. The Mounting Strap (F) contains several pairs of
threaded holes, find the pair of holes that match the
holes spacing in your fixture Back Plate (H) and thread
the two Mounting Screws (D) half way into the Mounting
Strap (F) and secure with Hex Nut (G).

4. Place the Mounting Strap (F)over the Junction Box

as required by fixture type.

5. Attach the Mounting Strap (F) to the Junction Box
using the two mounting screws (H)and tighten securely
with screw driver.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).

7. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the
green Ground Screw (I) on the Mounting Bracket (F) or
connect both wires together using the correct size of
wire connectors.

Fig. 1

twist the wire connector (L) onto the wires.

8. Tuck these wire connections neatly into the Junction
Box.

(Fig.3)

9. After tucking these wire connections neatly into the
Junction Box, place the fixture Back Plate (H) over the
two Mounting Screws (B).

10. Secure the Back Plate (H) against the wall by
threading two Deco Nuts (P) over the two Mounting
Screws (D) until tight as shown on Fig.1.

11. Install the light bulbs and glass shade as per the
fixture assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.