Golden Lighting 3711-9 CB User Manual

PARTS & ASSEMBLY SHEET
Fixture Name: Rockefeller 2488-9 FI & 3711-9 CB
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting screws Top loop
1ea 6-1/2"*H1-1/2" 2ea 8#32-IP*1" 1ea 1/8-IP*H60mm
Chain Wire connectors Nipple
1ea 6ft 4.2 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea 5.8*H61mm 1ea 1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Top cap Hex nut Cover
1ea 6-3/4"*H57mm 1ea 1/8-IP*H4mm 1ea 3/4"*H4mm
Part Needed Quantity
Part Needed Quantity Reason why ( missing, scratched, broken glass, bent, bad finish) Comments
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting strap
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before assembling the fixture.
ASSEMBLING THE FIXTURE (Fig.1)
1. Gently spread the arms until evenly spaced if arms are
packed closed.
2. Feed the fixture wires through the Top cap (M), Hex nut,
(W) Cover (U) and Top loop (J) and pull the wires until taut.
3. Then place the Top cap over threaded center column of
Frame (S) and secure in place with the Hex nut (W).
4. Place the Cover (U) onto the Top cap (M) and thread the
Top loop (J) on until tight.
NOTE: I
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
2488-9 FI & 3711-9 CB
Fig 1
24883711-PartsInstallation_20110105m.xls
PARTS & ASSEMBLY SHEET
ASSEMBLING THE FIXTURE (Fig.2)
9. Slip Canopy loop collar (B2) over the chain, then do the
sockets (P), secure the Glass Shades (O) by threading by
Fixture Name: Rockefeller 2488-9 FI & 3711-9 CB
5. Align the arms over the arm connector screws (V) at
base of fixture and secure in place with the Deco nuts (T)
that were attached there.
6. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers to
open one link of the Chain (C2) then remove the excess
Chain (C2) and discard it.
Fig 2
7. Use one chain connector(E2) to attach one end of the
chain to the Top loop (J) and close the chain connector.
8. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.
same with the canopy (F2).
10. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
the canopy loop (A2) and close the chain connector.
11. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Fig 3
Note: Complete these remaining steps after the fixture is
hung.
12. Place the Glass Shades (O) over the Threaded
the Socket Rings (N) until tight.
13. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
24883711-PartsInstallation_20110105m.xls
Loading...
+ 1 hidden pages