Page 1
2ea @3/8 x 3mm
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
For Customer Service, contact the place of purchase to arrange for replacement parts.
This fixture assembled PO:__________ Date: _ ____ ___
PARTS LIST
Company Name:_______________________ Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
Fig. 1
Read and review installation ins truction sheet before
assembling the fixture.
Fixture Name: Waverly 3500- 5/8 AB
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Canopy Wire Connectors Top Loop
1ea D6"×H1" 3ea P3 Orange 1ea W50 x 60mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain
Connector
2ea @4.2X50mm 1ea @3/8 x 40mm
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
F
IXTURE ASSEMBLY INSTRUCTIONS
Junction Box
Screw
Canopy Loop
with Collar
1ea @3/8 x 40mm x 5mm
Hex Nut
Spring Washer
Nipple
3500- 5/8 AB
1. Thread the thr eaded Stem (P) into the
coupling at center of fixture Body (R).
2. Thread the Top Loop (J) onto Stem (P). Handtighten until snug.
Page 2
PARTS & ASSEMBLY SHEET (cont.)
Fixture Name: 3500- 5/8 AB
Fig. 2
ASSEMBLING THE FIXTURE (Fig. 2)
3. Measure to determine the correct number of links
needed for proper hanging he ight . Us e a pair of
pliers to open one link of Chain (K) then remove
the excess chain and discard it.
4. Use Chain Connector ( L) to attach one end of
the chain to the Top loop (J). Then, close the chain
connector.
5. Feed the fixture wires through every three links of
chain and pull the wires until taut.
7. Slip Canopy loop collar (H) over the chain, then do the
same with the canopy (G).
6. Slip Canopy Loop Collar (H) over the chain, then
do the same with the Canopy ( G).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
7. To complete the installation, use the other
the canopy loop (F) and close the chain connector.
chain connector and attach the other end of
the chain to Canopy Loop (F) and close the
9. Make sure the weight of the chandelier will be
chain connector.
supported by the chain-not the electrical wire.
8. Make sure the weight of the chandelier will be
* You may now install t he fixture.
supported by the chain, no t t h e electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
9. Install the light bulbs ( not provided) in
accordance with the fixture' s specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
10. Carefully press the clips inside of Shade (Q)
onto the bulb.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
13. Raise Canopy (G) to the ceiling and secure in place by
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
Fig. 1
7. Unscrew the Canopy Loop Collar (H ) from the canopy loop.
should fit snugly on the canopy loop after the canopy is installed.
CONNECTING THE WIRES (Fig. 2)
NOTE: Twist the wires together in the same direction that you twisted
Fig. 2
INSTALLATION INSTRUCTIONS
Fixture Name: Waverly 3500- 5/8 AB
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
bag that holds all parts. Check that all parts are included as
shown in the illustration and the Parts and Assembly Sheet.
2. Shut off the power at the circuit breaker and completely
remove the old fixture from ceiling, including the old mount ing
strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with the canopy loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) which should
protrude through Mounting Strap (D). Then thread Hex Nuts (A)
onto Nipple (C) until tig ht.
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten the screws securely wit h a
screw driver.
For Chandelier Light Fixture
Take the canopy and pass over the canopy loop. Approximately
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *The Canopy loop collar
Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or a secure support
to hold the weight of the fixture while you complete the wiring
connections. 9.Thread
the fixture wires and ground wire of the assembled fixture through
the canopy loop and nipple and into the ou tlet box.
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE ( or
RIBBED) .
11. Ground wire connection: Connect the fixture ground wire to
house ground wire, which usually has green or copper insulation,
with the correct size of wire connector. If there is no house ground
wire at ceiling junction box then attach fixture ground wire
securely onto green grounding screw located on t he mounting
bar.
the wire connector onto the wires.
12. Tuck the wire connections neatly into the Junction Box.
tightening the Canopy loop collar (H) into the Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...