Page 1
Company Name:_______________________Co. Account #:_____________
Read and review installation instruction sheet
before assembling the fixture.
Fig 1
PARTS & ASSEMBLY SHEET
Fixture Name: Moreno 3281-9 BI
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all pa rts before assembling the fixture. If any parts are miss ing
or damaged, please note onthis sheet and c onta ct t he pl ace of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting screws
1ea ∅6"*H1-5/8" 2ea 8#32-IP*1"
Chain
1ea 6ft ∅5.0 3ea P3 Orange 1ea 1/4-IP*H60mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Candle Sleeves
9ea ∅1-1/4"*5-1/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out by retailer
Top loop
1ea 1/4-IP*H60mm
Wire connectors Nipple
Canopy loop
with Collar
Mounting strap
FIXTURE ASSEMBLY INSTRUCTIONS
3281-9 BI
ASSEMBLING THE FIXTURE (Fig. 1)
1. Feed the fixture wires through the Top loop (J) and
pull the wires until taut.
2. Then screw the Top Loop (J) and Spacer (I) onto
the threaded center column of Nipple (N) until tight.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
ASSEMBLING THE FIXTURE (Fig. 2)
Note: Complete the remaining steps after the fixture is
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Fig 2
PARTS & ASSEMBLY SHEET
Fig 4
Fixture Name: Moreno 3281-9 BI
3. Feed the fixture wires through Top Loop (J) and pull
the wires until taut.
4. Screw Top Loop (J) onto the threaded center
column of the frame until tight.
5. Measure to determine the correct number of chain
links needed for proper hanging height. Use a pair of
pliers to open one link of the chain to remove and
discard any excess chain.
6. Use one chain connector to attach one end of the
chain to the Top Loop (J) and close the chain
connector.
7. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
8. Slip Canopy Loop Collar (H) over the chain, then do
the same with the Canopy (G).
9. When ready to complete the installation, use the
other chain connector and attach the other end of the
chain to the canopy loop and close the chain
connector.
10. Make sure the weight of the chandelier will be
supported by the chain and not by the electrical wire.
* You may now install the fixture.
hung.
11. Install the light bulbs in accordance with the
fixture's
specifications.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
attached into Mounting Strap (D).
will protrude through Mounting Strap ( D) and thread Hex Nuts
Fig. 1
7. Unscrew Canopy Loop Collar (H ) from Canopy Loop (F) .
should be exposed. Adjust until the desired height is reached.
wiring connections.
box.
CONNECTING THE WIRES (Fig 2)
WHITE (or RIBBED).
Ground Screw on Mounting Bracket (D) or connect both wires
twist the wire connector ont o t he wires.
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
14. Install the light bulbs as per the fixture assembly sheet .
Fixture Name: Mor en o 3281-5/9/3P BI
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the cart on and the
yellow bag that holds all parts. Check that all parts ar e
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and r emove the
old fixture from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C) with the canopy loop
5. Place Lock Washer (B) over the end of Nipple (C) which
(A) onto the nipple until tight.
6. Take this mounting strap assembly and mount it to ceiling
junction box with Junction Box Screws (E). Tighten the
screws securely with screw driver.
Take the canopy and pass it over the canopy loop.
Approximately one half of the canopy loop exter ior threads
The canopy loop collar should fit snugly on the canopy loop
after the canopy is installed. Remove the canopy and canopy
lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete the
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
11. Attach the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
tightening Canopy Loop Collar (H) into Canopy Loop (F)
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...