Golden Lighting 3281-5 BI User Manual

Page 1
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
Fixture Name: Moreno 3281-5 BI
Fig 1
Read and review installation instruction sheet
F
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Mounting screws Top loop
1ea ∅6"*H1-5/8" 2ea 8#32-IP*1"
Chain
1ea 6ft 3.8 3ea P3 Orange 1ea 1/4-IP*H65mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Candle Sleeves
5ea ∅1-1/4"*5-1/8"
Part Needed Quantity Part Needed Quantity
Reason why Comments
to be filled out b y retailer
1ea 1/8-IP*H60mm
Wire connectors Nipple
Canopy loop with Collar
Mounting strap
IXTURE ASSEMBLY INSTRUCTIONS
before assembling the fixture.
ASSEMBLING THE FIXTURE (Fig. 1)
1. Feed the fixture wires through Top Loop (J) and pull the wires until taut.
2. Screw Top Loop (J) to the threaded center column of Nipple (N) until tight.
For Customer Service, contact the place of purchase to arrange for replacement parts.
3281-5 BI
Page 2
Fig 4
ASSEMBLING THE FIXTURE (Fig. 2)
(M) over Socket (O).
PARTS & ASSEMBLY SHEET
Fig 2
3. Measure to determine the correct number of links needed for proper hanging height. Use a pair of pliers to open one link of Chain (K) then remove and discard the excess chain.
4. Use one Chain Connector (L) to attach one end of the chain to Top Loop (J) and close the chain connector.
5. Feed the fixture wires through the Chain (every three links) and pull the wires until taut.
6. Slip Canopy Loop Collar (H) over the chain, then do the same with Canopy (G).
Fixture Name: Moreno 3281-5 BI
7. When ready to complete the installation, use the other chain connector to attach the other end of the chain to the Canopy Loop (F) and close the chain connector.
8. Make sure the weight of the chandelier will be supported by the chain and not by the electrical wire. * You may now install the fixture.
Note: Complete the remaining steps after the fixture is hung.
9. Place Candle Sleeve
10. Install the light bulbs in accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
attached into Mounting Strap (D).
will protrude through Mounting Strap ( D) and thread Hex Nuts
Fig. 1
7. Unscrew Canopy Loop Collar (H ) from Canopy Loop (F) .
should be exposed. Adjust until the desired height is reached.
wiring connections.
box.
CONNECTING THE WIRES (Fig 2)
WHITE (or RIBBED).
Ground Screw on Mounting Bracket (D) or connect both wires
twist the wire connector ont o t he wires.
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
14. Install the light bulbs as per the fixture assembly sheet .
Fixture Name: Mor en o 3281-5/9/3P BI
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the cart on and the yellow bag that holds all parts. Check that all parts ar e included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and r emove the old fixture from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C) with the canopy loop
5. Place Lock Washer (B) over the end of Nipple (C) which
(A) onto the nipple until tight.
6. Take this mounting strap assembly and mount it to ceiling junction box with Junction Box Screws (E). Tighten the screws securely with screw driver.
Take the canopy and pass it over the canopy loop. Approximately one half of the canopy loop exter ior threads
The canopy loop collar should fit snugly on the canopy loop after the canopy is installed. Remove the canopy and canopy lock collar.
8. Assemble the fixture and have an assistant or secure support hold the weight of the fixture while you complete the
9.Thread the fixture wires and ground wire of the assembled fixture through the canopy loop and nipple and into the outlet
10. Attach the power supply wires to the fixture lead w ires by connecting BLACK to BLACK (or SMOOTH) and WHITE to
11. Attach the GROUND wire (GREEN or COPPER) from the Junction Box and the fixture Ground wire to the green
together using the correct size of wire connectors. NOTE: Twist the wires together in the same direction you
tightening Canopy Loop Collar (H) into Canopy Loop (F)
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BO X AND
TEST THE FIXTURE.
Loading...