Page 1
PARTS & ASSEMBLY SHEET
Fixture Name: Moreno 3281-3P BI
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
Read and review installation instruction sheet
Fig 1
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy
1ea ∅6"*H1-5/8" 2ea 8#32-IP*1"
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H65mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/8"*H42mm 1ea W4-1/8"*E1"*H5mm
Candle Sleeve
3ea ∅1-1/4"*3-1/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
IXTURE ASSEMBLY INSTRUCTIONS
F
to be filled out b y retailer
Mounting screws
Canopy loop
with Collar
Top loop
1ea 1/8-IP*H60mm
Mounting strap
before assembling the fixture.
ASSEMBLING THE FIXTURE (Fig. 1)
1.Straining the wire and use the chain(O) to attach the
hook（N）。
For Customer Service, contact the place of purchase to arrange for replacement parts.
3281-3P BI
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET
ASSEMBLING THE FIXTURE (Fig. 2)
5. Feed the fixture wires through the Chain (every three
(P) over Socket (Q).
Fig 2
Fig 4
Fixture Name: Moreno 3281-3P BI
3. Measure to determine the correct number of links
needed for proper hanging height. Use a pair of pliers
to open one link of the chain and remove and discard
any excess.
4. Use one Chain Connector (L) to attach one end of
the chain to the Top Loop (M) and close the chain
connector.
links) and pull the wires until taut.
6. Slip Canopy Loop Collar (H) over the chain, then do
the same with the Canopy (G).
7. When ready to complete the installation, use the
other chain connector and attach the other end of the
chain to the Canopy Loop (F) and close the chain
connector.
8. Make sure the weight of the chandelier will be
supported by the chain and not by the electrical wire.
* You may now install the fixture.
Note: Complete the remaining steps after the fixture is
hung.
9. Place the Candle Sleeve
10. Install the light bulbs in accordance with the
fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Page 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
attached into Mounting Strap (D).
will protrude through Mounting Strap ( D) and thread Hex Nuts
Fig. 1
7. Unscrew Canopy Loop Collar (H ) from Canopy Loop (F) .
should be exposed. Adjust until the desired height is reached.
wiring connections.
box.
CONNECTING THE WIRES (Fig 2)
WHITE (or RIBBED).
Ground Screw on Mounting Bracket (D) or connect both wires
twist the wire connector ont o t he wires.
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
14. Install the light bulbs as per the fixture assembly sheet .
Fixture Name: Mor en o 3281-5/9/3P BI
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the cart on and the
yellow bag that holds all parts. Check that all parts ar e
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and r emove the
old fixture from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C) with the canopy loop
5. Place Lock Washer (B) over the end of Nipple (C) which
(A) onto the nipple until tight.
6. Take this mounting strap assembly and mount it to ceiling
junction box with Junction Box Screws (E). Tighten the
screws securely with screw driver.
Take the canopy and pass it over the canopy loop.
Approximately one half of the canopy loop exter ior threads
The canopy loop collar should fit snugly on the canopy loop
after the canopy is installed. Remove the canopy and canopy
lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete the
9.Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
10. Attach the power supply wires to the fixture lead w ires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
11. Attach the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
tightening Canopy Loop Collar (H) into Canopy Loop (F)
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BO X AND
TEST THE FIXTURE.
Loading...