Page 1
Screw
Decorative chains
Fig. 1
Canopy Loop
PARTS LIST
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
PARTS & ASSEMBLY SHEET
Fixture Name: HARLA N D 3 086 -3P CH
This fixture assembled PO:__________ Date: _ ____ ___
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Read and review installation ins truction sheet before
screw with the Top Loop (J) until tight.
J
M
Q
P
N
O
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Canopy Wire Connectors Top Loop
1ea 5"W× 3/4"H 3ea A4 Orange 1ea D50mm×H60mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain
Connector
2ea @4.X50mm 1ea @3/8 x 40mm x 5mm 1ea @1/2 x 55mm
Junction Box
with Collar
Spring Washer
Nipple
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Hex Nut
2ea @1/2 x 4mm
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
1. Place Nut (M) over the threaded nipple
2. Place the Glass (P) over the Wood Ring (Q).
3. Attach Ropes (O) to the Wood Ring (Q) and hook
into the holes in the metal Check Ring (N).
3086-4P CH
3ea
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
Fig. 2
PARTS & ASSEMBLY SHEET
For Customer Service, contact the place of purchase to arrange for replacement parts.
E
D
A
C
B
H
L
K
G
J
M
Q
P
N
O
Fixture Name: Athena 3086-BP4 CH
ASSEMBLING THE FIXTURE (Fig. 2)
2. Measure to determine the correct number of
links needed for proper hanging height. Use a pair
of pliers to open one link of Chain (K). Remove
and discard excess Chain (K).
3. Use one Chain Connector (L) to attach one end
of the chain toTop Loop (J) then close the chain
connector.
4. Feed the fixture wires through the chain (every
three links) and pull the wires until taut.
5. Slip Canopy Loop Collar (H) over the chain,
then do the same with Canopy (G).
6. When ready to complete the installation, use
the remaining chain connector to attach the other
end of the chain to Canopy Loop (F). Then close
the chain connector.
7. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
Page 3
Fig. 1
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
G
CHAIN
L
H
F
E
D
JUNCTION BOX
(CEILING)
A
C
B
INSTALLATION INSTRUCTIONS
Fixture Name: HARLAND 3086-M1L/3P/4P CH
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustrations and on the Parts and Assem bly Sheet.
2. Shut off the power at the circuit breaker and remove the old
fixture from ceiling, including the old m ounting s trap.
3. Thread Nipple (C) onto Canopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with Canopy Loop (F)
attached into Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which should
protrude through Mounting Strap (D). Then, thread Hex Nuts (A)
onto the nipple until tight.
6. Take this mounting strap assembly and m ount it to the ceiling
junction box with Junction Box Screws (E). T ighten the sc r ews
securely with screw driver.
7. Unscrew Canopy Loop Collar (H) from the canopy loop. T ake the
canopy and pass over the canopy loop. Approxim ately one half of
the canopy loop exterior threads should be exposed. Adj us t until
the desired height is reached. Note: The Canopy loop collar s hould
fit snugly on the canopy loop after the canopy is installed. Remove
the canopy and canopy lock collar.
8. Assemble the fixture and have an assistant or secur e support to
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
(or RIBBED).
11. Attach the GROUND wire (GREEN or COPPER) f r om the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires together
using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly into the J unct ion Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening Canopy Loop Collar (H) into Canopy Loop (F ).
14. Install the light bulbs as per the fixture assem bly sheet.
For Chandelier Light Fixture
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Loading...