Page 1
Decorative chains
PARTS & ASSEMBLY SHEET
Fixture Name: HARLA N D 3 086 -3P CH
This fixture assembled PO:__________ Date: _ ____ ___
Company Name:_______________________Co. Account #:_____________
For Customer Service, contact the place of purchase to arrange for replacement parts.
screw with the Top Loop (J) until tight.
Fig. 1
J
M
N
Q
O
P
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Wire Connectors Top Loop
1ea 5"W× 3/4"H 3ea A4 Orange 1ea D50mm×H60mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain
Connector
2ea @4.X50mm 1ea @3/8 x 40mm x 5mm 1ea @1/2 x 55mm
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out by retailer
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
2ea @1/2 x 4mm
Spring Washer
Nipple
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation ins truction sheet before
assembling the fixture.
3086-3P CH
1. Place Nut (M) over the threaded nipple
2. Place the Glass (P) over the Wood Ring (Q). 3.
Attach Ropes (O) to the Wood Ring (Q) and hook into
the holes in the metal Check Ring (N).
Page 2
PARTS & ASSEMBLY SHEET
Fig. 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
ASSEMBLING THE FIXTURE (Fig. 2)
E
D
A
C
B
G
L
K
G
J
M
N
Q
O
P
H
2. Measure to determine the correct number of links
needed for proper hanging height. Use a pair of pliers
to open one link of Chain (K). Remove and discard
excess Chain (K).
3. Use one Chain Connector (L) to attach one end of
the chain toTop Loop (J) then close the chain
connector.
4. Feed the fixture wires through the chain (every three
links) and pull the wires until taut.
5. Slip Canopy Loop Collar (H) over the chain, then do
the same with Canopy (G).
6. When ready to complete the installation, use the
remaining chain connector to attach the other end of
the chain to Canopy Loop (F). Then close the chain
connector.
7. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
Fixture Name: Athena 3086-BP3 CH
Page 3
Fig. 1
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
G
CHAIN
L
H
F
E
D
JUNCTION BOX
(CEILING)
A
C
B
INSTALLATION INSTRUCTIONS
Fixture Name: HARLAND 3086-M1L/3P/4P CH
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustrations and on the Parts and Assem bly Sheet.
2. Shut off the power at the circuit breaker and remove the old
fixture from ceiling, including the old m ounting s trap.
3. Thread Nipple (C) onto Canopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with Canopy Loop (F)
attached into Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which should
protrude through Mounting Strap (D). Then, thread Hex Nuts (A)
onto the nipple until tight.
6. Take this mounting strap assembly and m ount it to the ceiling
junction box with Junction Box Screws (E). T ighten the sc r ews
securely with screw driver.
7. Unscrew Canopy Loop Collar (H) from the canopy loop. T ake the
canopy and pass over the canopy loop. Approxim ately one half of
the canopy loop exterior threads should be exposed. Adj us t until
the desired height is reached. Note: The Canopy loop collar s hould
fit snugly on the canopy loop after the canopy is installed. Remove
the canopy and canopy lock collar.
8. Assemble the fixture and have an assistant or secur e support to
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
(or RIBBED).
11. Attach the GROUND wire (GREEN or COPPER) f r om the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires together
using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly into the J unct ion Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening Canopy Loop Collar (H) into Canopy Loop (F ).
14. Install the light bulbs as per the fixture assem bly sheet.
For Chandelier Light Fixture
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
Loading...