Page 1
2ea @3/8 x 3mm
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
1. Thread the th readed Stem (P) into the coupling
on clockwise rotation until tight.
Fig. 1
Read and review installa tion ins truction sheet before
assembling the fixture.
For Customer Service, contact the place of purchase to arrange for replacement parts.
This fixture assembled PO:__________ Date: ________
PARTS LIST
Company Name:_______________________ Co. Account #:_____________
to be filled out by r etailer
1ea @3/8 x 40mm x 5mm
PARTS & ASSEMBLY SHEET
J
R
Q
I
N
P
Fixture Name: Wynn 3082-M3/6/8 PW
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Canopy Wire Connectors Top Loop
1ea D5-1/8"*H1" 3ea P3 Orange 1ea W50 x 60mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector
2ea @4.2X50mm 1ea @3/8 x 40mm
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
Nipple
FIXTURE ASSEMBLY INSTRUCTIONS
ASSEMBLING THE FIXTURE (Fig. 1)
at center of fixture Body (R).
2. Thread the Top Loop (J) onto Stem (P). HandÂtighten until snug.
3. Put the Glass shade(Q) into the Cup. Keep
level while attaching upper arms (I). Attach
upper arms by screwing the thumb screw (N).
Then put the Thumb Screw (N) through Deco Arm
(I)
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
3082-M3/6/8 PW
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET (cont.)
Fig. 2
R
Q
I
N
P
G
C
D
K
L
H
F
J
Fixture Name: Wynn 3082-M3/6/8 PW
ASSEMBLING THE FIXTURE (Fig. 2)
4. Measure to determine the correct number of links
needed for proper h anging height. Use a pair of
pliers to open one link of Chain ( K ) then remove
the excess chain and discard it.
5. Use Chain Connector (L) to attach one end of
the chain t o the Top loop (J). Then, clos e the chain
connector.
6. Feed the fixture wi res through every three links of
chain and pull the wires until taut.
7. Slip Canopy loop collar (H) over the chain, then do the
same with the canopy (G).
7. Slip Canopy L o o p Coll a r (H) over the chain, then
do the same with the Canopy (G).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
8. To complete the installation, use the other
the canopy loop (F) and close the chain connector.
chain connector and attach the other end of
the chain to Canopy Loop (F) and close the
9. Make sure the weight of the chandelier will be supported
chain connector.
by the chain-not the electrical wire.
* You may now install the fixture.
9. Make sure the weight of the chandelier will be
supported by the chain, not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
10. Install the light bulbs (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Page 3
7. Unscrew the Canopy Loop Collar (H ) from the canopy loop. Take
canopy loop and nipple and into the out let box.
CONNECTING THE WIRES (Fig. 2)
Fig. 2
INSTALLATION INSTRUCTIONS
13. Raise Canopy (G) to the ceiling and secure in place by tighte ning
HANGING THE FIXTURE (Fig.1)
Fig. 1
E
G
C
D
B
JUNCTION
BOX
(CEILING)
A
K
L
H
F
Fixture Name: Wynn 3082-M3/6/8 PW
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown in
the illustration and the Parts and Assembly Sheet.
2. Shut off the power at the circuit breaker and completely remove
the old fixture from the ceiling, including the old mounting strap .
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with the canopy loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) which should
protrude through Mounting Strap (D). Then thread Hex Nuts (A) onto
Nipple (C) until tight.
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten the screws securely with a
screw driver.
For Chandelier Light Fixture
the canopy and pass over the canopy loop. Approximately one half
of the canopy loop exterior threads should be exposed. Adjust until
desired height is reached . *The Canopy loop collar should fit snugly
on the canopy loop after the canopy is installed. Remove Canopy
and Canopy lock collar.
8. Assemble the fixture and have an assistant or a secure support to
hold the w eight of the fixture while you complete the wiring
connections. 9.Thread
the fixture wires and g rou nd wire of the assembled fixture through the
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE ( or
RIBBED) .
11. Ground wire connection: Connect the fixture ground wire to house
ground wire, which usually has green or copper ins u lation, with the
correct size of wire connector. If there is no house ground wire at
ceiling junction box then attach fixture ground wire securely onto
green grounding screw located on the mounting b ar.
NOTE: Twist the wires together in the same direction that you twisted
the wire connector onto the wires.
12. Tuck the wire connections ne atly into the Junction Box.
the Canopy loop collar (H) into the Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture assembly
sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX A ND
TEST THE FIXTURE.
Loading...