Golden Lighting 3082-M1L PW User Manual
1ea 4" 2ea 8/32"X28mm 2ea 8/32X1"
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
For Customer Service, contact the place of purchase to arrange for replacements.
F
Read and review installation instruction sheet
before assembling the fixture.
Cover (P) by threading Socket Ring (Q) unitl tight.
Fig. 1
NOTE: INSTALL THE GLASS ASSEMBLY
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
J
G
P
K
L
H
F
I
O
M
Q
Y
R
Fixture Name: Wynn 3082-M1L PW
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
or damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap Mounting Screw Mounting screw
Wire
connnector
3ea P3 Orange 2ea 8/32"X3.5mm 2ea @10mm
Canopy Rod Socket Ring Tool
1ea D 5-1/8"*H1"
Part Needed Quantity
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
1. By measuring determine correct number of rods
needed for proper hanging height.
* This fixture includes 4 rods (6", 12", 12", 12")
2. To shorten the fixture, slide the excess rods off the
wires. To lengthen, add additional rods.
3. Pull the fixture’s wires through Rods (H,I,J,K) until
taut and thread the rods together. Then thread the
rods onto Fixture Body (L), and the swivel joint on
Canopy (G).
4. Slide Glass Shade (M) over the socket of Fixture
Body (L).Then put Socket Ring (Q) into the Socket
Ring Tool (Y). Secure the glass and metal Socket
Hex Nut Deco nut
3ea 12.7mm* H12“ 1ea 12.7mm* H6”
1ea D50mm*H110mm
3082-M1L PW
(round nut)
5. Attach Decorative Arms ( R) to the fixture base by
inserting and tightening Thumb Screws (O).
6. Install the light bulb in accordance with the fixture's
specification.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
AFTER THE FIXTURE IS HUNG.
INSTALLATION INSTRUCTIONS
Fig. 2
Fig. 3
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fig. 1
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
C
B
G
A
F
OUTLET BOX
(CEILING)
C
B
G
A
F
Fixture Name: Wynn 3082-M1L PW
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixtur e from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and on the Parts and
Assembly Sheet.
2. Shut off power at the circuit breaker and com pletely r emove
the old fixture from wall, including the old m ounting s trap.
3. Mounting Strap (A) contains several pairs of threaded holes,
find the pair of holes that match the holes spacing in your f ix ture
Canopy (G) and thread the two Mounting Screws (B) into
Mounting Strap (A). Secure with Hex Nuts (C). The threaded
ends will protrude through the two holes in the f ixtur e canopy.
4. Place Mounting Strap (A) over Junction Box (E) s o that
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.
5. Attach Mounting Strap (A) to Junction Box (E) by using the
two Mounting Screws (D). Tighten the sc r ews sec ur ely.
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
6. Attach the GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture ground wire to the green G r ound
Screw on the Mounting Bracket (A) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
9. Place Fixture Canopy (G), over Mounting Sc rews ( B), which
should protrude through the holes in the Canopy ( G ).
10. Thread Deco Nuts (F) onto the Mounting Screws (B) and
continue turning until the Canopy (G) is snug against the ceiling.
11. Install glass shades as per the fixture assembly instructions.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
For Pendant Light Fixture
Loading...