Page 1
1ea 102X320mm 2ea 8/32"X5/8''mm 2ea 8/32X1"
Finial
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Company Name:_______________________Co. Account #:_____________
below to be filled ou t by retailer
Read and review installation instruction sheet before
PLEASE NOTE:
The twisted candles are preassembled onto the fixture body.
NOTE: I
GND
F
F-1
F-2
G
G
E
Fixture Name: ATHENA 3071- WSC GG
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap Mounting Screw Mounting screw
Wire connnector
3ea P3 Orange 1ea 8/32"X10mm 1ea 3/8"*H40mm
Part Needed
Part Needed Quantity
Green Ground
screw
Nipple
18*12MM Quantity
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
1. Attach and hang Decorative Chains (F-1 & F-2) into hook
(E). 2.
Install the light bulb in accordance with the fixture's
specification.
3071-WSC GG
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact t he place of purchase to arrange for r eplacement parts.
Page 2
FINISHING THE INSTALLATION (Fig. 3)
Secure Finial (D) by twisting until tight.
FIXTURE.
Fig. 3
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1) 1.
old fixture from the ceiling, including the old mounting strap.
3. Place Mounting Strap (B) over the junction box. 4.
driver.
Fig. 1
CONNECTING THE WIRES (Fig. 2)
correct size of wire connectors. NOTE: Twist
wire connections neatly into the Junction Box.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
A
B
C
A
B
D
F
E
C
Fixture Name: ATHENA 3071-WSC GG
Carefully remove the new fixture from the carton and the yellow
bag that holds all of your parts. Check that all parts are included
as shown in the illustrations and on the Parts and Assembly
Sheet. 2.
Shut off the power supply at the circuit breaker and remove the
Attach Mounting Strap (B) to the junction box using the two
Mounting Screws (A). Tighten the screws securely using a screw
5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED). 6.
Attach the GROUND wire (GREEN or COPPER) from the junction
box and the fixture Ground wire to the green Ground Screw on
Mounting Bracket (A) or connect both wires together using the
For Wall Mount Light Fixture
the wires together in the same direction that you twist the wire
connectors onto the wires. 7. Tuck these
8. Raise the assemble light fixture to the wall so that it covers the
junction box. 9. Line
the screw holes up on both sides of Mounting Strap (A) with the
holes of the fixture's backplate. 10. Secure
the backplate of the light fixture to the junction box using the four
small screws. Tighten the screws securely using a screw driver.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...