2ea @1/2 x 4mm
Decorative chains
3ea
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Fig. 1
Read and review installation instruction sheet before
assembling the fixture.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
J
M
K
Fixture Name: Athena 3071-M3 GG
Notice: Please review the parts listing and check for al l parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement part s.
Canopy Wire Connectors Top Loop
1ea 5-5/8"W× 2-5/8"H 3ea A4 Orange 1ea D50mm×H60mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain
Connector
2ea @4.X50mm 1ea @3/8 x 40mm x 5mm 1ea @1/2 x 75mm
Mounting Strap
w/ ground screw
1ea 3/4"X4"
Part Needed Quantity
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
Nipple
FIXTURE ASSEMBLY INSTRUCTIONS
3071-M3 GG
Note: The Canopy, Chain, and Twisted Candles
are preassembled onto the fixture body.
1. Place Top Cap (M) over the threaded nipple
of Top Loop (J) and twist until snug. Then hook to
attach and hang Decorative Chains (K) .
PARTS & ASSEMBLY SHEET
Fixture Name: Athena 3071-3P GG
Fig. 2
For Customer Service, contac t the place of purchase to arrange for replacement parts.
For Customer Service, contact the place of purchase to arrange for replacement parts.
H
F
E
D
A
C
B
L
K
G
J
M
L
K
ASSEMBLING THE FIXTURE (Fig. 2)
2. Measure to determine the correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of Chain (K). Remove and
discard excess Chain (K).
3. Use one Chain Connector (L) to attach one end
of the chain toTop Loop (J) then close the chain
connector.
4. Feed the fixture wires through the chain (every
three links) and pull the wires until taut.
5. Slip Canopy Loop Collar (H) over the chain, then
do the same with Canopy (G).
6. When ready to complete the installation, use the
remaining chain connector to attach the other end
of the chain to Canopy Loop (F). Then close the
chain connector.
7. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
Fig. 1
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
JUNCTION BOX
(CEILING)
A
C
B
G
CHAIN
L
H
F
E
D
Fixture Name: Athena 3071-M3 GG
For Chandelier Light Fixture
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are included
as shown in the illustrations and on the Parts and Assembly
Sheet.
2. Shut off the power at the circuit breaker and remove the old
fixture from ceiling, including the old m ounting s tr ap.
3. Thread Nipple (C) onto Canopy Loop (F) until snug.
4. Thread the other end of the Nipple (C) with Canopy Loop (F)
attached into Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which
should protrude through Mounting Strap (D). Then, thread Hex
Nuts (A) onto the nipple until tight.
6. Take this mounting strap assembly and m ount it to the
ceiling junction box with Junction Box Screws ( E). Tighten the
screws securely with screw driver.
7. Unscrew Canopy Loop Collar (H) from the canopy loop.
Take the canopy and pass over the canopy loop.
Approximately one half of the canopy loop exterior threads
should be exposed. Adjust until the desired height is reac hed.
Note: The Canopy loop collar should fit snugly on the canopy
loop after the canopy is installed. Remove the canopy and
canopy lock collar.
8. Assemble the fixture and have an assistant or secur e
support to hold the weight of the fixture while you complete the
wiring connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire (GREEN or COPPER) f r om the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the J unc tion Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening Canopy Loop Collar (H) into Canopy Loop (F ).
14. Install the light bulbs as per the fixture assem bly sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...