Golden Lighting 3071-BA4 GG User Manual

1ea 102X320mm 2ea 8/32"X5/8''mm 2ea 8/32X1"

screw

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS LIST

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

Read and review installation instruction sheet before
assembling the fixture.

1. Hang Decorative Chains (I) onto Fixture Body (J).

shorten. Rubbing alcohol is recommended to clean the bulbs if

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

I

H

G

F
E

Fixture Name: ATHENA 3071-BA4 GG

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

Mounting strap Mounting Screw Mounting screw

Wire connnector

3ea P3 Orange 1ea 8/32"X10mm

Part Needed Decorative Chains Quantity
Part Needed Quantity

Green Ground

FIXTURE ASSEMBLY INSTRUCTIONS

3071-BA4 GG

2. Slide Glass Shade (H) over Socket (E) and secure in place
using Metal Spacer Ring (F) and Socket Ring (G). Screw on
Socket Ring (G) until tight.

3. Install the light bulb in accordance with the fixture's
specification. Bulb
note: Use a tissue or paper towel to hold the bulb and push
down into the socket. Oils or dirt can cause the bulb life to

dirty.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

HANGING THE FIXTURE (Fig. 1) 1.

shown in the illus trations and on the Parts and Assembly Sheet.

old fixture from t he ceiling, incl uding the old mounting strap.

Fig. 1

CONNECTING THE WIRES (Fig. 2)

these wire connections neatly into t he Junction Box.

Fig. 2

FINISHING THE INSTALLATION (Fig. 3)

small scr ews. Tighten the sc rews securely using a screw driver.

FIXTURE.

Fig. 3

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

A

B

A

B

H

G

F

E

C

D

Fixture Name : ATHENA 3071-BA1/2/3/4/ GG

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

Carefully remove the new fixture from the carton and the yellow
bag that holds all of your parts. Check that all parts are included as

2. Shut off the power supply at the circuit breaker and remove the

3. Place Mounting Strap (B) over the junction box. 4.
Attach Mounting Strap (B) to the junction box using the two
Mounting Screws (A). Tighten the screws securely using a screw
driver.

5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED). 6.
Attach the GROUND wi re (GREEN or COPPER) f rom the junction
box and the fixture Ground wire t o the green Ground Screw on
Mounting Bracket (A) or connect both w ires together using the
correct size of wire connectors. NOTE:
Twist the wires together in the sam e direction that you t wist the
wire connectors onto the wires. 7. Tuck

For Wall Mount Light Fixture

8. Raise the assem ble light fixture to the wall so that it covers the
junction box. 9. Line
the screw holes up on both sides of Mounti ng Strap (A) with the
holes of the fixture's backplate. 10. Secure
the backplate of t he light fixture to the junction box using the four

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE

For Customer Service, contact the place of purchase to arrange for replacement parts.