Golden Lighting 3071-BA3 GG User Manual
3071-BA-140417 Instruction sheet
1ea 102X320mm 2ea 8/32"X5/8''mm 2ea 8/32X1"
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
NOTE: I
1. Hang Decorative Chains (I) onto Fixture Body (J).
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled ou t by retailer
H
G
F
I
E
Fixture Name: ATHENA 3071-BA3 GG
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Mounting strap Mounting Screw Mounting screw
Wire connnector
3ea P3 Orange 1ea 8/32"X10mm
Part Needed Crystal Chain Quantity
Part Needed Quantity
Green Ground
screw
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
2. Slide Glass Shade (H) over Socket (E) and secure in place
using Metal Spacer Ring (F) and Socket Ring (G). Screw on
Socket Ring (G) until tight.
3. Install the light bulb in accordance with the fixture's
specification. Bulb note:
Use a tissue or paper towel to hold the bulb and push down
into the socket. Oils or dirt can cause the bulb life to shorten.
Rubbing alcohol is recommended to clean the bulbs if dirty.
3071-BA3 GG
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact t he place of purchase to arrange for r eplacement parts.
FINISHING THE INSTALLATION (Fig. 3)
small scr ews. Tighten the screws securely us ing a screw driver.
FIXTURE.
Fig. 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig. 1) 1.
shown in the illus trations and on the Parts and Assembly Sheet.
old fixture from t he ceiling, including the old mounting str ap.
Fig. 1
CONNECTING THE WIRES (Fig. 2)
these wire connections neatly into the Junction Box.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
A
B
A
B
H
G
F
E
C
D
Fixture Name : ATHENA 3071-BA1/2/3/4/ GG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Carefully remove the new fixture from the carton and the yellow
bag that holds all of your parts. Check that all parts are included as
2. Shut off the power supply at the circuit breaker and remove t he
3. Place Mounting Strap (B) over the juncti on box. 4.
Attach Mounting Strap (B) to the juncti on box using the two
Mounting Screws (A). Tighten the sc rews securely us ing a screw
driver.
5. Attach the power supply wires to the f ixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED). 6.
Attach the GROUND wi re (GREEN or COPPER) from the junction
box and the fixture Ground wire t o the green Ground Screw on
Mounting Bracket (A) or connect both wires together usi ng the
correct size of wire connectors. NOTE:
Twist the wires together in the same direction that you tw ist the
wire connectors onto the wires. 7. Tuck
For Wall Mount Light Fixture
8. Raise the assem ble light fixture to t he w all so that it c overs the
junction box. 9. Line
the screw holes up on both sides of Mounting Strap (A) with the
holes of the fixture's backplate. 10. Secure
the backplate of t he light fixture to the junc tion box using the four
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange fo r replacement parts.
Loading...