Golden Lighting 3071-BA2 GG User Manual
1ea 102X320mm 2ea 8/32"X5/8''mm 2ea 8/32X1"
Green Ground
screw
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
Read and review installation instruction sheet before
assembling the fixture.
1. Hang Decorative Chains (I) onto Fixture Body (J).
specification. Bulb note:
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
E
I
J
H
G
F
Fixture Name: ATHENA 3071-BA2 GG
Notice: Please review the parts listing and check for all pa rts before assembling the fixture. If any parts are miss ing or
damaged, please note on this s heet a nd c ontac t the place of purchase to arrange for replacement parts.
Mounting strap Mounting Screw Mounting screw
Wire connnector
3ea P3 Orange 1ea 8/32"X10mm
Part Needed Decorative Chains Quantity
Part Needed Quantity
FIXTURE ASSEMBLY INSTRUCTIONS
2. Slide Glass Shade (H) over Socket (E) and secure in place
using Metal Spacer Ring (F) and Socket Ring (G). Screw on
Socket Ring (G) until tight.
3. Install the light bulb in accordance with the fixture's
Use a tissue or paper towel to hold the bulb and push down
into the socket. Oils or dirt can cause the bulb life to shorten.
Rubbing alcohol is recommended to clean the bulbs if dirty.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
THE FIXTURE IS HUNG.
3071-BA2 GG
For Customer Service, contact the place of purchase to arrange for replacement parts.
FINISHING THE INSTALLATION (Fig. 3)
small scr ews. Tighten the screw s securely using a s crew driver.
FIXTURE.
Fig. 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig. 1) 1.
shown in the illus trations and on the Parts and Assembly Sheet.
old fixture from t he ceiling, including the old mounting strap.
Fig. 1
CONNECTING THE WIRES (Fig. 2)
these wire connections neatly into the J unction Box.
Fig. 2
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
A
B
A
B
H
G
F
E
C
D
Fixture Name : ATHENA 3071-BA1/2/3/4/ GG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Carefully remove the new fixture from the carton and the yellow
bag that holds all of your parts. Check t hat all parts are inc luded as
2. Shut off the power supply at the circuit breaker and remove the
3. Place Mounting Strap (B) over the junction box. 4.
Attach Mounting Strap (B) to the junction box usi ng the two
Mounting Screws (A). Tighten the screws securely using a screw
driver.
5. Attach the power supply wires to the fi xture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED). 6.
Attach the GROUND wi re (GREEN or COPPER) fr om the junction
box and the fixture Ground wire t o the green Ground Screw on
Mounting Bracket (A) or connect both wires together using the
correct size of wire connectors. NOTE:
Twist the wires together in the same direction that you twist the
wire connectors onto the wires. 7. Tuck
For Wall Mount Light Fixture
8. Raise the assem ble light fixture to the wall so that it cover s the
junction box. 9. Line
the screw holes up on both sides of Mounting Strap (A) with the
holes of the fixture's backplate. 10. Secure
the backplate of t he light fixture to the junction box using the four
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...