Golden Lighting 3030-BA4 CH User Manual
#8-32n*10mm
Spacer
Xenon Bulb
Socket Tool
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation ins truction sheet
before assembling the fixtur e.
Fig. 4
1. Attach Front Plate (F) onto the Mounting
4. Install the Light B ulb (M) in accordance with
PARTS & ASSEMBLY SHEET
Fixture Name: Vanora 3030-BA4 CH
replacement parts.
PARTS LIST
Company Name:_______________________Co . Account #:_____________
below to be filled out by r etailer
220V 25W
G9
N
F
M
L
K
J
I
H
G
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note on this sheet and contact the place of purchase to arrange for
Anchor
2 ea
6*H15mm
Ø
Deco Nut
2 ea
Ø 8"*H8mm
4 ea 14*13*44MM
Part Needed
Part Needed Quantity
FIXTURE ASSEMBLY INSTRUCTIONS
Screws (D) located at center line of
Mounting Plate (B) and secure them together
by threading Deco Nut ( I) onto Front Plate ( F ).
2. Slide Outer Glass Shade (H ) over Socket (G). (Not e:
The gap at the bottom of the glass shoul d be turned
toward the inside) Sli de Inner Glass Shade (J) and
Spacer (K) over Socket (G) . Secure Glass Shades (H),
(J), and Spacer (K), in place using Socket Tool (N) to
thread Socket Ring (L) onto Socket (G) until tight.
Junction Box
Screw
#8-32N*25mm
Wire Connector
3 ea
P3
1 eaΦ28*127MM
Green Ground
Screw
1 ea
4 ea
5*H26mm
Ø2
Screw
Φ4*25MM
2ea
3030-BA4 CH
the fixture's specifi cations .
(DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!)
For Customer Service, contact the place of purchase to arrange for replacement parts.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Fig. 1
Fig. 2
HANGING THE FIXTURE(Fig.1)
4. Install the Light Bulb (M) in accordance with
the fixture's specifications .
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
B
A
D
C
FIXTURE WIRES
HOUSE WIRES
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
A
C
D
E
B
220V 25W
G9
N
F
M
L
K
J
I
H
G
1.Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and parts
list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3. Hold Mounting Plate (B) up against the wall aligning the
two holes in the Junction Box with the appropriate slots in
the Mounting Plate (B). Then while the
Mounting Plate (B) is leveled horizontally, use a pen or
pencil to make a mark on the wall at holes located near
each end of Mounting Plate (B). Set aside the
Mounting Plate (B) and insert Wall Anchors (A) into the
two marks made on the wall.
4. Thread the supply wires and ground wire from Junction
Box through center holes in Mounting Plat e (B).
5. Attached the Mounting Plate (B) to Junction Box by using
the two Junction Box Screws (E). If Anchors (A) were
attached to the wall, secure the Mounting Plate (B) with
two Anchors Screws (C) to corresponding holes.
CONNECTING THE WIRES (Fig. 2)
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
7. Attached the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the
green Ground Screw on the Mounting Strap (B) or connect
both wires together using the correct size of wire
connectors
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION(Fig.3)
1. Attach Front Plate (F) onto the Mounting
Screws (D) located at center line of
Mounting Plate (B) and secure them together
by threading Deco Nut (I) onto Front Plate (F).
2. Slide Outer Glass Shade (H) over Socket (G). (Note: The gap
at the bottom of the glass should be turned toward the inside)
Slide Inner Glass Shade (J) and Spacer (K) over Socket (G) .
Secure Glass Shades (H), (J), and Spacer (K), in place using
Socket Tool (N) to thread Socket Ring (L) onto Socket (G) until
tight.
INSTALLATION INSTRUCTIONS
Fixture Name: Vanora 3030-BA4 CH
For Wall Mount Light Fixture
AND TEST THE FIXTURE.
Loading...