Golden Lighting 3030-BA1 CH User Manual

Deco Nut
27N*H12mm
Green Ground Screw
Spring Washer
Spacer
Xenon Bulb
Socket Tool
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
parts.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
Read and review installation instruction sheet before assembling the fixture.
1. Place fixture Back Plate (P), over Threaded Rod (D), so that it protrudes through the hole in
2. Thread Deco Nut (I) onto Threaded Rod (D) and continue turning until Back Plate (P) is snug
Fig. 4
220V 25W G9
H
I
J
K
L
M
N
P
O
Fixture Name: Vanora 3030-BA1 CH
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note o n this sheet and contact the place of purchase to arrange for replacement
Mounting Strap 1 ea Ø3/4*1"
Wire Connector 3 ea P3
1 ea #8-32N*H10mm
1 ea 14*13*44MM
Part Needed Quantity Part Needed Quantity
FIXTURE ASSEMBLY INSTRUCTIONS
Junction Box Screw 2 ea #8-32N*H25mm
Hex Nut 2 ea 3/8"*H3mm
1 ea
15*H3mm
Ø
Φ28*127MM
Thread Rod 1 ea 3/8"*H50mm
1 ea 3/8"-
1 ea
5*H26mm
Ø2
3030 BA1-CH
Back Plate (P).
against the wall .
3. Slide Outer Glass Shade (J) on over Socket (H). (Note: The gap at the bottom of the glass should be turned toward inside.) Then, slide Inner Glass Shade (K) and Spacer (L) over Socket (H). Secure Outer Glass Shade (J), Inner Glass Shade (K), and Spacer (L) in place using Socket Tool (O) to thread Socket Ring (M) onto the Socket (H) until tight.
4. Install the Light Bulb (N) in accordance with the fixture's specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fig. 3
Fig. 1 Fig. 2
HANGING THE FIXTURE(Fig.1)
fixture from wall, including the old mounting strap.
Hex Nut (B) and Spring Washer (C).
Threaded Rod (D), so that it protrudes through the hole in
2. Thread Deco Nut (I) onto Threaded Rod (D) and continue turning until Back Plate (P) is snug
Spacer (L) in place using Socket Tool (O) to thread Socket Ring
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE JUNCTION BOX
B
A
D
C
FIXTURE WIRES
HOUSE WIRES
Fig.2
JUNCTION BOX
GND
A
I
C
B
G
F
D
E
BARE COPPER
GREEN (Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK (Hot)
WHITE (Netural)
HOUSE WIRES
220V 25W G9
H
I
J
K
L
M
N
P
O
Fixture Name: Vanora 3030-BA1 CH
For Wall Mount Light Fixture
1.Carefully remove the new fixture from the carton and the yellow bag that holds all your parts. Check that all parts are included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
3.Take Threaded Rod (D) from parts bag and thread into center screw hole on Mounting Strap (A), tighten with
4. Attach the Mounting Strap (A) to the Junction Box (I) using the two Mounting Screws (E). Tighten the screws securely.
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
6. Attached the GROUND wire (GREEN or COPPER) from the Junction Box and the fixture Ground wire to the green Ground Screw on the Mounting Strap (B) or connect both wires together using the correct size of wire connectors NOTE: Twist the wires together in the same direction you twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
1. Place fixture Back Plate (P), over
Back Plate (P).
against the wall .
3. Slide Outer Glass Shade (J) on over Socket (H). (Note: The gap at the bottom of the glass should be turned toward inside.) Then, slide Inner Glass Shade (K) and Spacer (L) over Socket (H). Secure Outer Glass Shade (J), Inner Glass Shade (K), and
(M) onto the Socket (H) until tight.
4. Install the Light Bulb (N) in accordance with the fixture's specifications.
AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...