Page 1
Mounting Strap
Canopy
Swivel Joint
Deco Nut
Rods
Green Ground
Rod
Xenon Bulb
1 ea
Mounting Screw
Junction Box
Screw
#8-32N*25mm
Wire Connector
Socket Tool
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture as sembled P O:__________ Date: ________
Fixture Name: Baxley 2081-MIL CH
Read and review installation instruction sheet before
assembling the fixture.
1. For adjusting the hanging height of the fixture, this carton
DO NOT EXCEED THE MAXIMUM WATTAGE RATING
Fig. 4
J
H
I
F
G
E
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
or damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
1 ea
4"*3"*H1.5mm
2 ea
5/32"*9mm
1 ea
Ø1/2"*H6"
2 ea
5/32"*28mm
1 ea
Φ28*93MM
Part Needed
Part Needed Quantity
1 ea
Φ115*19MM
3 ea
Ø1/2"*H12"
14*13*44MM
2ea
1 ea
3/8"*H57mm
Screw
1 ea
#8-32n*10mm
Spacer
3 ea
Ø25*H26mm
3 ea
P3
FIXTURE ASSEMBLY INSTRUCTIONS
2081-MIL CH
contains quantity 3, 12" rods and quantity 1, 6" rod. First,
decide the height required. Then, thread T hreaded Rod
Nipples (I) into the Fixture Coupler (J), and thread Rods (H) to
Threaded Rod Nipples (I). Redo this st ep f or the rest of Rods
(H).
2. Once attached, connec t the top of Threaded Rod Nipple (I)
to Universal Joint (G)
3. Connect Rods (H) and Threaded Rod Nipples (I) toget her
and feed the fixture wires through Rods (H). Pull the
fixture wires until taut.
For Customer Service, contac t the place of purchase to arrange for replacement parts.
Page 2
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fig. 3
Fig. 1
Fig. 2
HANGING THE FIXTURE (Fig.1)
10. Slide Glass Shade (N), Spacer (M) over Socket (O) and
secure Glass Shades (N), and Spacer (M) by using
Socket Tool (Q) to thread the Socket Ring (L) onto
11. Install Light Bulbs (K) in accordance with
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
FIXTURE WIRES
HOUSE WIRES
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
A
D
C
JUNCTION BOX
(CEILING)
B
F
M
K
L
N
Q
O
Fixture Name: Baxley 2081-MIL CH
For Chandelie r Light Fixture
1.Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts
are included as shown in the illustrations and the Parts and
Assembly Sheet.
2. Shut off power at the circuit breaker and completely remove the
old fixture from ceiling, including the old mounting strap.
3. Space the the two fixture Mounting Screws (A) the same distance
apart as the holes in the Canopy (E) and thread the two fixture
Mounting Screws (A) into Mounting Strap (B). Secure in place using
Hex Nuts (D).
4. Attached Mounting Strap (B) to the Junction Box using
the two Mounting Screws (C).
CONNECTING THE WIRES (Fig.2)
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE ( or RIBBED) .
6. Attach GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the
Green Ground Screw on the Mounting Strap (B) or
connect both wires together using the correct size of
wire connectors.
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the ceiling
Junction Box.
FINISHING THE INSTALLATION
8. Place Canopy (E) over Mounting Strap (B) and over the Mounting
Screws (A). Adjust Canopy (E) until the Mounting Screws (C)
protrude through Canopy (E) and secure the fixture against ceiling
by threading Deco Nut (F) until tight.
Securing the Glass Panels (Fig. 3)
the Socket (O) until tight.
the fixture's specifications.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...