Golden Lighting 2081-5 CH User Manual
Mounting Strap
Canopy
Swivel Joint
Hex Nut
2ea
Spring Washer
2 ea
15*H3MM
Green Ground
Deco Nut
Rods
Rod
Glass Finial
Xenon Bulb
1 ea
25*H26mm
Mounting Screw
Junction Box
Screw
#8-32N*25mm
Wire Connector
Wrench
1 ea
Arm
2 ea
Socket Tool
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet before
assembling the fixture.
1. Secure Arms (P) t o Hous i ng (V) by using Wrench (W),
For the top assembly, tighten Housing Cover (R) to
Housing (V) with Check Ring (X).
together. Pull the fixture wires until taut.
Fig. 4
or damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture as sembled P O:__________ Date: ________
V
T
R
S
P
U
W
J
H
I
F
G
E
V
R
X
Fixture Name: Baxley 2081-5 CH
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
PARTS LIST
1 ea
4"*3"*H1.5mm
3/8"*H4MM
2 ea
5/32"*9mm
1 ea
3/8"*H8mm
2 ea
5/32"*28mm
28*60MM
Part Needed
Part Needed Quantity
1 ea
Φ115*19MM
3 ea
Ø1/2"*H12"
14*13*44MM
2ea
187*455mm
1 ea
3/8"*H57mm
Screw
1 ea
#8-32n*10mm
1 ea
Ø1/2"*H6"
Spacer
3 ea
Ø
3 ea
P3
1 ea
Φ28*127MM
FIXTURE ASSEMBLY INSTRUCTIONS
2081-5 CH
at the top and the bottom of the fixture, to attach Spri ng
Washer (U) and Hex Nut (T). For the bott om assembly,
tighten the Housing Cover (R) to Housing (V) with Fini al (S).
2.For adjusting the hanging height of the fixture, this carton
contains quantity 3, 12" rods and quantity 1, 6" rod. First,
decide the height required and thread the wires through Rods
(H). Then connect Rods (H) and Threaded Rod Nipples (I)
3. Connect the assem bl ed Rods (H) t o F i xture Frame (J).
4. Connect Threaded Rod Nipple (I) to Swivel Joint (G).
DO NOT EXCEED THE MAXIMUM WATTAGE RATING
For Customer Service, contac t the place of purchase to arrange for replacement parts.
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Fig. 1
Fig. 2
HANGING THE FIXTURE (Fig.1)
10. Slide Glass Shade (N), Spacer (M) over Socket (O) and
secure Glass Shades (N), and Spacer (M) by using
Socket Tool (Q) to thread Socket Ring (L) onto
11. Install Light Bulbs (K) in accordance with
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
UNCTION BOX
AND TEST THE FIXTURE.
FIXTURE WIRES
HOUSE WIRES
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
A
D
C
JUNCTION BOX
(CEILING)
B
F
M
K
L
N
Q
O
1.Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts
are included as shown in the illustrations and the Parts and
Assembly Sheet.
2. Shut off power at the circuit breaker and completely remove the
old fixture from ceiling, including the old mounting strap.
3. Space the the two fixture Mounting Screws (A) the same distance
apart as the holes in the Canopy (E) and thread the two fixture
Mounting Screws (A) into Mounting Strap (B). Secure in place using
Hex Nuts (D).
4. Attached Mounting Strap (B) to the Junction Box using
the two Mounting Screws (C).
CONNECTING THE WIRES (Fig.2)
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE ( or RIBBED) .
6. Attach GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the
Green Ground Screw on the Mounting Strap (B) or
connect both wires together using the correct size of
wire connectors.
NOTE: Twist the wires together in the same direction
you twist the wire connector onto the wires.
7. Tuck these wire connections neatly into the ceiling
Junction Box.
FINISHING THE INSTALLATION
8. Place Canopy (E) over Mounting Strap (B) and over the Mounting
Screws (A). Adjust Canopy (E) until the Mounting Screws (C)
protrude through Canopy (E) and secure the fixture
against ceiling by threading Deco Nut (F) until tight.
Securing the Glass Panels (Fig. 3)
INSTALLATION INSTRUCTIONS
Fixture Name: Baxley 2081-5 CH
For Chandelie r Light Fixture
Socket (H) until tight.
the fixture's specifications.
AND TEST THE FIXTURE.
Loading...