Golden Lighting 2073-M1L WG User Manual

For Customer Service, contact the place of purchase to arrange for replacement parts.
Fixture Name: SMYTH 2073-M 1L GMT
Notice: Please review the P arts Li st and check for all parts before assembling the fixture. If any
are missing or damaged, please note on this sheet and contact the place of purchase to
arrange for replacement parts.
Company Name:______________ Co Account#:__________ below to be filled out by retailer
Green Screw G8/32*H8
Hex Nut G5/32*H4
ea
12
2073-M1L GMT
Fig.1
correct number of
8. Thread Canopy (E) into Rod (H) until tight.
E F G
H
I
parts
PARTS LIST
PART S & ASSEMBLY SHEET
Mounting Strap Φ102 1ea
Wire Connectors Orange 3ea
Canopy 1 L126*W126*H25
” Rod Φ 12*L305
3ea
1ea
2ea
Mounting Screws H32㎜ 2ea H38㎜2ea
Deco Nut Φ12*12 2ea
6” Rod Φ12*L152 1ea
Part Needed ______________________________ Quantity _________________________________ Part Needed ______________________________ Quantity _________________________________ Reason why (missing, scratched, broken glass, bent, bad finish) Comments __________________________________________________________________________
FIXTURE ASSEMBL Y INSTRUCTIONS
Read and review installation instruction sheet before assembling the fixture
1. Measure to determine the
rods needed for proper hanging height. There are 3 optional 12" rods and a 6” rod included.
2. To shorten the fixture, trim the wires to the desired length and add at least 8~10 inches. You must use at least the 6” rod.
3. To lengthen the fixture, add additional rods. (ROD-12 CDB ) is available. To purchase additional rods, please contact the retailer.
4. Pull the fixture’s wires through the rods.
5. Place Washer (G) between Rod (H) and Frame (I). Thread Rod (H) into Frame (I) until tight.
6. Place Washer (G) between each rod and thread until tight.
7. Feed the fixture wires through Ca n opy (E) and pull the wires until taut.

2073-M1L GMT PARTS AND ASSEMBLY SHEET

F For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: SMYTH 2073-M 1L GMT
Mini Pendant Light Fixture
HANGING THE FIXTURE (Fig.1)
Fig. 1
Fig.2
Fig.3
FIXTURE WIRES
SMOOTH (or Black)
RIBBED (or White)
BARE COPPER (or Green)
HOUSE WIRES
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
JUNCTION BOX (CEILING)
A
B C
D E
F
JUNCTION BOX (CEILING)
A E
F
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
1. Carefully remove the new fixture from the carton as well as the yellow parts bag. Check that all parts are included as sh o w n in t he illustrations and the Parts and Assembly Sheet.
2. Shut off power at the circuit b reaker and completely remove the old fixture from ceiling, including the old mou n ting strap.
3. The Mounting Strap (B) contains several pairs of threaded holes, find the pai r of ho les that ma tches the holes spacing in yo ur fixture canopy (E). Thread Fixture Mount ing Screws (A) half way into the Fixture Mounting Strap (B).
4. Place the Mounting St rap (B) over the Junction Box so that Mounting Screws (A) are vertical or horizontal, as required by the fixture type.
5. Attach the Fixture Mounting Strap (B) to the Junction Box using Mounting Screws (C). Tighten the screws securely with a screw driver.
CONNECTING THE WIR E S(Fig.2)
6. Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK (or SM OOTH) and WHITE to WHITE (or RIBBED).
7. Ground Wire Connection: Connect the fixture ground wire to the supply ground wire (this usually has green insulat ion) w ith wire conn ector. If there is no supply ground wire at ce iling junction box then attach the fixture ground wire secure ly onto green grounding screw located at mo unt in g bar.
NOTE: Twist the wires together in the same direction you twisted the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION(Fig.3)
9. Place Canopy (E) over Mounting Screws (A) and secure Canopy (E) against the wall by threading Deco Nuts (F) over Mounting Screws (A) until tight as shown on Fig.3.
10. Install the light bulb in accordance with the fixture’s specifications.
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

2073-M1L INSTALLATION INSTRUCTIONS PART 1

Loading...