Golden Lighting 2073-4 WG User Manual
For Customer Service, contact the place of purchase to arrange for replacement parts.
This fixture assembled PO: Date:
Fixture Name: SMYTH 2073-4 GMT
Notice: Please review the Parts List and check for all parts before assembling the fixture. If any
are missing or damaged, please note on this sheet and contact the place of purchase
to arrange for replacement parts.
Company Name:_____________ Co Account#:__________
below to be filled out by retailer
Green Screw
G8/32*H8
Hex Nut
G
Nipple
3/8
Threaded
1ea
Φ23
6. Slide Glass Shades (T) on the lam p fitters.
2073-4 GMT
Fig.1
G
CHAIN
J
H
F
K
R
T
U
S
V
parts
PARTS LIST
PART S & ASSEMBLY SHEET
Mounting Strap
3/4"*1" 1ea
Wire Connectors
Orange 3ea
Tube
Φ22*50mm 4ea
Chain
1ea 6FT*Φ4.2mm
Chain Connector
2 ea Φ4*H55mm
3/8*H4 ㎜ 2ea
”*H45MM 1ea
㎜ 1ea
Ring
-16T*H5mm
Mounting Screws
㎜
2ea
H32
Top Loop
57*65 ㎜ 1ea
Canopy 1ea
126*126*H25MM
Screw Collar Loop
1ea 3/8"*H42.4mm
Part Needed ________________ ______________ Quantity _________________________________
Part Needed ________________ ______________ Quantity ________________________ _________
Reason why (missing, s cratched, broken glass, be nt, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBL Y INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
1. Feed the fixture wires through Rod (V) to
Center Rod (K) and connect the rods
well.
2. Hook the top of Center Rod (K) to the Top
Loop (J).
3. Connect the Top Loop (J) to the chain.
4. Hook Hanger Rods (R ) to the Frame (S),
then hook the top of Hanger Rods (R) to
the Top Loop (J).
5. Slide the Candle Sleeves (U) over the
sockets.
2073-4 GMT PARTS AND ASSEMBLY SHEET
F For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: SMYTH 2073-4 GMT
For Chandelier Light Fixture
HANGING THE FIXTURE (Fig.1)
Fig. 1
Fig.2
YOUR INSTALLATION IS NOW COMPLETE.
FIXTURE
HOUSE
G
CHAIN
J
H
F
E
D
JUNCTION BOX
(CEILING)
A
C
B
WARNING! SHUT POWER OFF AT F USE OR CIRCUIT BREAKER
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are
included as shown in the illustration and the Parts List.
2. Shut off the power at the circuit breaker and remove the
old fixture from the ceiling, including the old mounting
strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C) with Canopy Loop (F)
attached into Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which
should protrude through Mounting Strap (D). Thread Hex
Nuts (A) onto Nipple (C) until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box using Junction Box Screws (E). Tighten the
screws securely with screw driver.
7. Unscrew the Canopy Loop Coll a r (H ) from Ca n op y Lo op
(F). Take the Canopy (G) and pass over the Canopy Loop
(F). Approximately one half of the Canopy Loop (F) exterior
threads should be exposed. Adjust until desired height is
reached, The Canopy Loop Collar (H) should fit snugly on
Canopy Loop (F) after the canopy is installed. Remove
Canopy (G) and Ca no py Loop Collar (H)
8. Assemble the fixture and have an assistant or secure a
support to hold the weight of the fixture while you comple te
the wiring connections.
9. Thread the fixture wires and ground wires of the assembled
fixture through the chain loops, Canopy Loop (F), Nipple
(C) and into the Junction Box.
CONNECTING THE WIRES (Fig.2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED) .
Ground wire connection: Connect the fixture
11.
ground wire to the supply ground wire (this usually has
green insulation) with wire connector. If there is no
supply grou nd wire at c eil ing junction box then attach
the fixture ground wire securely onto the green
grounding screw located at mo unt in g bar.
NOTE: Twist the wires together in the same direction you
twisted the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy Loop Collar (H) into the Canopy
Loop (F).
14. Install the light bulbs and glass shade as per the Parts and
Assembly Sheet.
WIRES
SMOOTH
(Or Black)
RIBBED
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE
2073-4 GMT INSTALLATION INSTRUCTIONS PART 1
WIRES
BLACK
(Hot)
WHITE
Loading...