Golden Lighting 2073-3P WG User Manual
For Customer Service, contact the place of purchase to arrange for replacement parts.
This fixture assembled PO: Date:
Fixture Name: SMYTH 2073-3P GMT
Notice: Please review the Parts List and check for all parts before assembling the fixture. If any
are missing or damaged, please note on this sheet and contact the place of purchase
to arrange for replacement parts.
Company Name:_____________ Co Account#:__________
below to be filled out by retailer
Green Screw
G8/32*H8
Hex Nut
G
Nipple
3/8
Threaded
1ea
Φ23
6. Slide Glass Shades (T) onto the lamp fitters.
2073-3P GMT
Fig.1
G
CHAIN
J
H
F
K
R
S
T
U
V
parts
PARTS LIST
PART S & ASSEMBLY SHEET
Mounting Strap
3/4"*1" 1ea
Wire Connectors
Orange 3ea
Tube
Φ22*50mm 3ea
Chain
1ea 6FT*Φ4.2mm
Chain Connector
2 ea Φ4*H55mm
3/8*H4 ㎜ 2ea
”*H45MM 1ea
㎜ 1ea
Ring
-16T*H5mm
Mounting Screws
㎜
2ea
H32
Top Loop
57*65 ㎜ 1ea
Canopy 1ea
126*126*H25MM
Screw Collar Loop
1ea 3/8"*H42.4mm
Part Needed ________________ ______________ Quantity _________________________________
Part Needed ________________ ______________ Quantity _________________________________
Reason why (missing, s c ratched, b roken glass, b ent, bad finish)
Comments __________________________________________________________________________
FIXTURE ASSEMBL Y INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
1. Feed the fixture wires through Rod (V) to
Center Rod (K) and connect the rods
well.
2073-3P GMT PARTS AND ASSEMBLY SHEET
2. Hook the top of Center Rod (K) to the Top
Loop (J).
3. Connect the Top Loop (J) to the chain.
4. Hook Hanger Rods (R ) to the Frame (S),
then hook the top of Hanger Rods (R) to
the Top Loop (J).
5. Slide the Candle Sleeves (U) over the
sockets.
F For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: S MYTH 2073-3P GMT
For Chandelier Light Fixture
HANGING THE FIXTURE (Fig.1)
Assembly Sheet.
Fig. 1
Fig.2
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
FIXTURE
HOUSE
G
CHAIN
J
H
F
E
D
JUNCTION BOX
(CEILING)
A
C
B
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
1. Carefully remove the new fixture from the carton along
with the yellow bag that holds all parts. Check that all parts
are included as shown in the illustrations and Parts and
Assembly Sheet.
2. Shut off the power at the circuit breaker and remove the
entire old fixture from ceiling, including the old mounting
strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C) with Canopy Loop (F)
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto
nipple (C) until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box screws (E). Tighten screw
securely with screw driver.
7. Unscrew the Canopy Loop Coll a r (H ) from Ca n op y Lo op
(F). Take the Canopy (G) and pass over the Canopy Loop
(F).Approximately one half of the Canopy Loop (F) exterior
threads should be exposed. Adjust until desired height is
reached. The Canopy Loop Collar (F) should fit snugly on
the Canopy Loop (F) after the Canopy is installed. Remove
Canopy (G) and Canopy Lock Collar (H)
8. Assemble the fixture and have an assistant or a secure
support to hold the weight o f the fixtur e while yo u complete
the wiring connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the chain loops, Canopy Loop (F), Nipple
(C) and into the Junction Box.
CONNECTING THE WIRES (Fig.2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE ( or RIBBED) .
Ground wire connection: Connect fixture’s ground
11.
wire to supply ground wire (this usually has green
insulation ) with wire connector. If there is no supply
ground wire at the ceiling junction box then attach
fixture ground wire securely on to green grounding
screw that is located at the mounting bar.
NOTE: Twist the wires together in the same direction you
twisted the wire connector onto the wires.
12. Tuck these wire connections neatly into the ceiling
Junction Box.
13. Raise Canopy (G) to the ceiling and secure it in place by
tightening the Canopy Loop Collar (H) into the Canopy
Loop (F).
14. Install the light bulbs and glass shade as per the Parts and
WIRES
SMOOTH
(Or Black)
RIBBED
AND TEST THE FI XTURE
2073-3P GMT INSTALLATION INSTRUCTIONS PART 1
WIRES
BLACK
(Hot)
WHITE
Loading...