Page 1
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting Strap (D)
Green Ground Screw
Wire Connectors
Read and review installation instruction sheet before
3. Tighten Top loop (J).
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fixture Name: Valencia 2049-M1L FB
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy
Hex Nut (A)
Nipple (C)
1ea 5.2"DIA*1.1"
Chain
1 ea 6FT*Φ4.2mm
Chain Connector
2 ea Φ4*H55mm
1 ea 3/4"*1"
Top Loop (J)
1 ea W42*H53mm
Part Needed Quantity
1ea 3/8"*H3mm
Threaded Ring (H)
1ea Φ23-16T*H5mm
Screw Collar Loop (F)
1ea 3/8"*H42.4mm
1 ea #8-32N*H10mm
Crystal (K)
2 ea W21*63Lmm
1ea 3/8"*H45mm
Spring Washer (B)
1ea Φ15*H3mm
Junction Box Screw (E)
2 ea #8-32N*H32mm
3 ea P3
Glass
4ea
W110*H160mm
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
Fig. 1
2049-M1L FB
1. Slide the Glass panels (L) into the box, then
secure with clips.
2. Hang the Crystals (K).
NOTE: INSTALL THE GLASS ASSEMBLY BEFORE
THE FIXTURE IS HUNG.
Page 2
PARTS & ASSEMBLY SHEET
G
CHAIN
H
F
E
J
K
L
Fixture Name: Valencia 2049-M1L FB
ASSEMBLING THE FIXTURE (Fig . 2)
4. By measuring determine correct number of
links needed for proper hangi ng heig ht. U se a
pair of pliers to open one link of the Chain then
remove the excess Chain and discar d it .
5. Use one chain connector to attach one end of
the chain to the Top loop (J) and close the chai n
connector.
6. Feed the fixture wir es through the C hai n
(every three links) and pull the wires until taut.
7. Slip Canopy loop collar over the chai n, then
do the same with the canopy.
8. When ready to complete the instal l ati on U se
the other chain connector and at tach the other
end of the chain to the canopy loop and cl ose
the chain connector.
9. Make sure the weight of the fixture is
supported by the chain-not the electrical wire.
*You may now hang the fixture
10. Install the light bulb in accor dance w ith the
fixture's specifications.
DO NOT EXCEED MAXIMUM WATTAGE
RATING!
Fig 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
Fig. 2
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
G
CHAIN
J
H
F
E
D
JUNCTION BOX
(CEILING)
A
C
B
Fixture Name: Valencia 2049-4P/6/9/M1L FB
For Pendant Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixtur e from the carton and
the yellow bag that holds all par t s. Check that all parts
are included as shown in t he illustrat ion and parts list.
2. Shut off the power at the circuit breaker and remove
old fixture from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C)
protruding through Mounting Strap (D) and thread Hex
Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to
ceiling junction box with Mounting screws (E). Tighten
screw securely with screw dr iver.
7. Unscrew the Canopy loop collar( H ) from the
Canopy loop. Take the canopy and pass over the
Canopy loop. approximately one half of the canopy loop
exterior threads should be exposed. Adjust until desired
height is reached. *the Canopy loop collar should fit
snugly on the Canopy loop after t he c anopy is installed.
Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete
the wiring connections.
9.Thread the fixture wires and ground wire of the
assembled fixture through the canopy loop and nipple
and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture
wires by connecting BLACK to BLACK (or SMOOTH)
and WHITE to WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER)
from the Junction Box and t he fixtur e Ground wire to the
green Ground Screw on t he M ount ing Bracket (D) or
connect both wires together using the correct size of
wire connectors.
NOTE: Twist the wires together in t he same direction
you twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the
Junction Box.
FINISHING T HE INSTALLAT ION
13. Raise the Canopy (G) to t he ceiling. Secure in
place by tightening the Canopy Loop Collar (H) onto the
Canopy Loop (F).
Fig. 1
lead
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
For Customer Servic e, contact the place of purchase to arrange for re placement parts.
Loading...