Page 1
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Read and review installation instruction sheet before
assembling the fixture.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fixture Name: Joia 1993-M1L PS
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Wire Connectors Top Loop
1ea D150*H34mm 3e a A4 Orange 1ea
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
2ea @4.2X50mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 455mm
Mounting Strap
w/ ground screw
1ea 3/4"X4" 2ea @3/8 x 3mm
Part Needed Quantity
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
IXTURE ASSEMBLY INSTRUCTIONS
F
Note: The wire cage and fabric shade are
already assembled on the fixture body
1. Thread the top loop (J) onto t he nipple of fixture
body (M).Hand-tighten until snug.
1993-M1L PS
Fig. 1
Page 2
PARTS & ASSEMBLY SHEET
Fig. 2
C
D
Fixture Name: Joia 1993-M1L PS
ASSEMBLING THE FIXTURE (Fig. 2)
3. By measuring determine correct number of
links needed for proper hanging height. Use a
pair of pliers to open one link of the Chain (K)
then remove the excess Chain (K) and discard it.
4. Use one chain connector (L) to attach one end
of the chain to the Top loop (J) and close the
chain connector.
5. Feed the fixture wires through the Chain
(every three links) and pull the wires until taut.
6. Slip Canopy loop collar (H) over the chain,
then do the same with the canopy (G).
7. When ready to complete the installation Use
the other chain connector and attach the other
end of the chain to the canopy loop (F) and close
the chain connector.
8. Make sure the weight of the chandelier will be
supported by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
9. Install the light bulb (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
Fig. 2
L
B
C
A
JUNCTION BOX
(CEILING)
D
E
F
H
CHAIN
G
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Joia 1993- 5 /-9 /- M1L PS
For Pendant Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixtur e from the carton and the yellow
1. Carefully remove the new fixture from the carton and the yellow bag
bag that holds all parts. Check that all parts are
that holds all parts. Check that all parts are included as shown in the
in the illustration and parts list.
illustration and parts list.
2. Shut off the power at the circuit breaker and rem ove old fix ture
2. Shut off the power at the circuit breaker and remove old fixture from
from ceiling, including the old m ounting s tr ap.
ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F ) until snug.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attac hed
4. Thread other end of the Nipple (C) with Canopy Loop attached into
into Mounting Strap (D).
Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
5. Place Lock Washer (B) over end of Nipple (C) protruding through
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling junction box
6. Take this mounting strap assem bly and mount to ceiling
junction box with junction box Screws (E) . T ighten s c rew sec urely
with junction box Screws (E). Tighten screw securely with screw driver.
with screw driver.
7. Unscrew the Canopy loop collar(H )from the Canopy loop. Take the
7. Unscrew the Canopy loop collar (H )from the Canopy loop.
canopy and pass over the Canopy loop. approximatly one half of the
Take the canopy and pass over the Canopy loop. approx imatly
one half of the canopy loop exterior threads should be expos ed.
canopy loop exterior threads should be exposed. Adjust until desired
Adjust until desired height is reached. *the Canopy loop c ollar
height is reached. *the Canopy loop collar should fit snugly on the
should fit snugly on the Canopy loop after the canopy is installed.
Canopy loop after the canopy is installed. Remove Canopy and
Remove Canopy and Canopy lock collar.
Canopy lock collar.
8. Assemble the fixture and have an assis tant or sec ure support
8. Assemble the fixture and have an assistant or secure support hold
hold the weight of the fixture while you com plete the wiring
the weight of the fixture while you complete the wiring connections.
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
through the canopy loop and nipple and into the outlet box.
9. Thread the fixture wires and ground wire of the ass embled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or
connecting BLACK to BLACK (or SMOOTH) and WHITE to
RIBBED).
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the Junction
11. Attach the GROUND wire(GREEN or COPPER) from the
Box and the fixture Ground wire to the green Ground Screw on the
Junction Box and the fixture Ground wire to the green G round
Screw on the Mounting Bracket (D) or connect both wires
Mounting Bracket (D) or connect both wires together using the correct
together using the correct size of wire connectors.
size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
NOTE: Twist the wires together in the same direction you twist the wire
connector onto the wires.
12. Tuck these wire connections neatly into the J unc tion Box.
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
13. Raise Canopy (G) to the ceiling and secure in place by tightening
tightening the Canopy loop collar ( H) into the Canopy Loop( F) .
the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and shade as per the fixture ass embly
14. Install the light bulbs and glass shade as per the fixture assembly
sheet.
sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 1
included as shown
YOUR INSTALLATIO N I S NOW CO MPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...