Reason why( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Read and review installation instruction sheet before
assembling the fixture.
Notice:
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
For Customer Service, contact the place of purchase to arrange for replacement parts.
Q
P
O
N
M
P
U
T
S
R
Fixture Name: Madera 1821-SF BI
This fixture assembled PO:__________ Date: ________
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap
(circular)
1ea @4" 4ea P3 Orange2ea 12mm
Wire connectorsDeco nut
Canopy
1ea @5-1/2"X1-1/4"2ea 8/32" x 1"1ea 53 x 56mm
ChainMounting screw
1ea 6ft x3.8mm2ea 8/32" x 22" 2ea @3/8 x 40mm x 5mm
Chain connectorHex nut Nipple
2ea @3X38mm1ea @3/8 x 50mm
w/ ground screw
1ea 3/4"X4"
Part NeededQuantity
IXTURE ASSEMBLY INSTRUCTIONS
F
2ea/1ea @3/8 x 3mm/ @3/8 x 5mm
Top loop
Canopy loop
with Collar
1821-SF BI
Fig. 1
ASSEMBLING THE FIXTURE as Semi flush (Fig. 1)
1. Thread the Stem With Hex Nut (N) into the bottom coupling of
the Fixture body (M) until tight.
2. Slide the Flat Washer (O), Rubber Washer (P), Glass shade (Q),
Rubber Washer (P) and Frame (R) over the Stem With Hex Nut
(N), secure in place with the Hex nut (R). Slide the Bottom cap (T)
over the Stem With Hex Nut (S), secure in place with the Finial (U).
3. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Page 2
Fig 2
PARTS & ASSEMBLY SHEET
C
D
U
T
S
R
Q
P
O
N
M
P
V
J
X
Fixture Name: Pemberly Court 1821-SFBI
ASSEMBLING THE FIXTURE as Chain hung (Fig.2)
1. Unscrew the Hex Nut (V), then take off the small lock
washer (W), flat washer (X) and canopy (Y).
2. Feed the fixture wires through the Top loop (J) and pull the
wires until taut.
3. Then screw the Top Loop (J) to the threaded center of
fixture body (M) until tight.
4. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (K) then remove the excess Chain (K) and
discard it.
5. Use one chain connector (L) to attach one end of the chain
to the Top loop (J) and close the chain connector.
6. Feed the fixture wires through the Chain (every three links)
and pull the wires until taut.
7. Slip Canopy loop collar (H) over the chain, then do the
same with the canopy (G).
8. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
canopy loop (F) and close the chain connector.
9. Make sure the weight of the chandelier will be supported
by the chain-not the electrical wire.
Note: Complete these remaining steps after the fixture is
hung.
11. Thread the Stem With Hex Nut (N) into the bottom
coupling of the fixtur body (M) until tight.
12.Slide the Flat Washer (O), Rubber Washer (P), Glass
shade (Q), Rubber Washer (P) and frame (R) over the Stem
With Hex Nut (N), secure in place with the Hex nut (S). Slide
the Bottom cap (T) over the Stem With Hex Nut (N), secure
in place with the Finial (U).
13. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
Fig. 3
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
E
Fixture Name: Madera 1821-SF BI
For Semi Flush / Convertible Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Semi Flush (Fig. 1)
1. Carefully remove the new fixture from the carton
and the yellow bag that holds all your parts. Check
that all parts are included as shown in the illustration
and parts list.
2. Shut off power at the circuit breaker and remove
the old fixture from wall, including the old mounting
strap.
3. The Mounting Strap (B) contains several pairs of
threaded holes. Find the pair of holes that matches
the holes spacing in your Canopy (F) and thread the
two Mounting Screws (A) into the Mounting Strap (B).
Secure in place with Hex nuts (D).
4. Place the Mounting Strap (B) over the junction box
so the Mounting Screws (A) will have their threaded
ends protrude through the two holes in the canopy
(F).
5. Attach the Mounting Strap (B) to the junction box
by using the two Mounting Screws (C). Tighten the
screws securely.
CONNECTING THE WIRES (Fig. 2)
6. Take the black wire from the ceiling junction box
and the smooth wire leg from the fixture and twist
bare ends together. Twist wire connector onto end of
wires until snug.
7. Repeat same process with white junction box wire
and ribbed wire of fixture.
NOTE: Twist wires together in the same direction
you twist the wire connector onto wires.
8. If your junction box has a grounding wire (green or
bare copper), attach this wire and the bare copper
wire from the fixture together as in step 7. If junction
box has no ground wire, attach the bare copper fixture
wire to the junction box with a screw.
9. Tuck these wire connections neatly into the
junction box.
FINISHING T HE INSTALLAT ION (Fig. 3)
10. Place the fixture’s Canopy (F) over the Mounting
Strap (B) and over the Mounting Screws (A). Adjust
the fixture canopy until the Mounting Screws (A)
protrude out from the canopy. Secure the fixture
against the ceiling by threading the Decorative Nuts
(E) on until tight.
11. Install the light bulbs and glass shade according
to the fixture assembly sheet
Fig. 1
Fig. 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 4
INSTALLATION INSTRUCTIONS
Fig. 2
L
B
C
A
JUNCTION BOX
(CEILING)
D
E
F
H
J
CHAIN
G
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Madera 1821-SF BI
For Pendant Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE(Fig.1)
1. Carefully remove the new fixtur e from the carton and the
yellow bag that holds all parts. Check that all parts ar e
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and rem ove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F ) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto
Nipple until tight.
6. Take this mounting strap assem bly and mount to ceiling
junction box with junction box Screws (E) . T ighten s c rews
securely with screw driver.
7. Unscrew the Canopy loop collar (H) fr om the Canopy loop.
Take the canopy and pass over the Canopy loop.
Approximately one half of the canopy loop ex ter ior thr eads
should be exposed. Adjust until desired height is reached.
*the Canopy loop collar should fit snugly on the Canopy loop
after the canopy is installed. Rem ove Canopy and C anopy
lock collar.
8. Assemble the fixture and have an assis tant or sec ure
support hold the weight of the fixture while you complete the
wiring connections.
9. Thread the fixture wires and ground wire of the ass embled
fixture through the canopy loop (F) and nipple (C ) and chain
(every three links) into the outlet box.
CONNECTING THE WIRES (Fig.2)
10. Attach the power supply wires to the fixt ure lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green G round
Screw on the Mounting Bracket (B) or connec t both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the sam e direction you
twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the J unc tion Box.
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar ( H) into the Canopy Loop
(F).
14. Install the light bulbs and glass shade as per the f ixtur e
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 1
YOUR INSTALLATIO N I S NOW CO MPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.