Golden Lighting 1821-FM BI User Manual

Page 1
Mounting Strap
Stem With Hex Nut
Washer
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet before assembling the fixture.
PARTS & ASSEMBLY SHEET
3/8-IP*H3mm / 8/32-IP*H3mm
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
F
G
H
I
J
K
I
L N
M
Fixture Name: Madera 1821-FM BI
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting screw
1ea L4"*H1.5mm
Hex nut Wire connnector Deco Nut
1ea / 2ea
Bottom cap Finial
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
4ea 8/32-IP*H1" 1ea @3/8 x 110mm
3 ea P4 Orange
2ea 12mmx 11mm
Flat Washer/Rubber
1ea/2ea @1-1/2" x 2mm1ea Φ75*H14mm 1ea 3/8-IP*H14mm

1821-FM BI

Fig 1
1. Thread the Stem With Hex Nut (G) into the Coupling of the Ceiling Pan (F) until tight.
2. Install the lighting bulbs in accordance with the fixture's specification.
3. Place the Flat Washer (H), Rubber Washer (I), Glass Shade (J), Rubber Washer (I), Scrolled cage (K) over the Stem (G) and thread Hex Nut (L) on until tight.
4. Slide Bottom Cap (M) over Stem With Hex Nut (G) and thread the Finial (N) until tight.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
Fig. 1
BARE COPPER
(Ground)
GREEN (Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
F
E
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow bag that holds all your parts. Check that all parts are included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old fixture from wall, including the old mounting strap.
3. The Mounting Strap (B) contains several pairs of threaded holes. Find the pair of holes that matches the holes spacing in your Canopy (F) and thread the two Mounting Screws (A) into the Mounting Strap (B). Secure in place with Hex nuts (D).
4. Place the Mounting Strap (B) over the junction box so the Mounting Screws (A) will have their threaded ends protrude through the two holes in the canopy (F).
5. Attach the Mounting Strap (B) to the junction box by using the two Mounting Screws (C). Tighten the screws securely.
CONNECTING THE WIRES (Fig. 2)
6. Take the black wire from the ceiling junction box and the smooth wire leg from the fixture and twist bare ends together. Twist wire connector onto end of wires until snug.
7. Repeat same process with white junction box wire and ribbed wire of fixture. NOTE: Twist wires together in the same direction you twist the wire connector onto wires.
8. If your junction box has a grounding wire (green or bare copper), attach this wire and the bare copper wire from the fixture together as in step 7. If junction box has no ground wire, attach the bare copper fixture wire to the junction box with a screw.
9. Tuck these wire connections neatly into the junction box.
FINISHING T HE INSTALLAT ION (Fig. 3)
10. Place the fixture’s Canopy (F) over the Mounting Strap (B) and over the Mounting Screws (A). Adjust the fixture canopy until the Mounting Screws (A) protrude out from the canopy. Secure the fixture against the ceiling by threading the Decorative Nuts (E) on until tight.
11. Install the light bulbs and glass shade according to the fixture assembly sheet YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name: Madera 1281-FM BI
For Flush Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
Fig. 2
Fig. 3
Loading...