Golden Lighting 1821-1W BI User Manual

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

PARTS & ASSEMBLY SHEET

Read and review installation instruction sheet before

Bulb

(Not Provided)

Fixture Name: Made r a 1821- 1W BI

This fixture assembled PO:__________ Date: ________

Notice:

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap

1ea 4" 2ea 8/32"X1" 2ea 8/32"X32mm

Wire Connnector Hex Nut

3ea P4 Orange 2ea 8/32"X3.5mm 2ea 12mm

Green Ground
Screw

1ea 8/32"X10mm

Part Needed Quantity
Part Needed Quantity

IXTURE ASSEMBLY INSTRUCTIONS

F

assembling the fixture.

Junction Box
Screw

Fig. 1

Mounting Screw

Deco Nut (round
nut)

1821-1W BI

1. Install the light bulb in accordance with the fixture' s
specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

For Customer Service, contact the place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

Fig. 2

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fixture Name: Madera 1821-1W BI

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig. 1)

1. Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all parts are
included as shown in the illustration and parts list.

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

3. The Mounting Strap (A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in your
fixture Back Plate (J) and thread the two Mounting Screws (B)
into the Mounting Strap (A). Secure in place with the Hex nuts
(C).

4. Place the Mounting Strap (A) over the Junction Box (E) so the
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.

5. Attach the Mounting Strap (A) to the Junction Box (E) by using
the two mounting screws (D). Tighten the screws securly.

CONNECTING THE WIRES (Fig. 2)

5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE
(or RIBBED).

6. Attach the GROUND wire(GREEN or COPPER) from the Junction
Box and the fixture Ground wire to the green Ground Screw on
the Mounting Bracket (A) or connect both wires together using
the correct size of wire connectors.
NOTE:Twist the wires together in the same direction you twist
the wire connector onto the wires.

7. Tuck these wire connections neatly into the Junction Box.

FINISHING THE INSTALLATION (Fig.3)

9. Place the fixture Back Plate (J), over the Mounting screws(B),
so they protrude through the holes in the Back Plate (J).

10. Thread the Deco Nuts (H) onto the Mounting Screws (B) and
continue turning until the Back Plate (J) is snug against the wall.

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

Fig. 1

Fig. 3

For Customer Service, contact the place of purchase to arrange for replacement parts.