Golden Lighting 1648-BA3 BUS User Manual

For Customer Service, contact the place of purchase to arrange for replacement parts.

This fixture assembled PO: Date:

Fixture Name: Olympia 1648-BA3 BUS

Notice: Please review the parts listing and check for all parts before assembling the fixture. If

are missing or damaged, please note on this sheet and contact the place of

purchase to arrange for replacement parts.

Company Name:_____________ Co Account#:__________
below to be filled out by retailer

Green Screw
G8/32*H8

Mounting Screws
8/32"X5/8''mm

Mounting Screws
2ea 8/32X1"

1648-BA3 BUS

Fig.1

any parts

PARTS LIST

PART S & ASSEMBLY SHEET

Mounting Strap
1ea 102X320mm

Wire Connectors
Orange 3ea

Anchor Screws
2ea N0.8X21''

Part Needed ________________ ______________ Quantity ____________ _____________________
Part Needed ________________ ______________ Quantity ____________ _____________________
Reason why (missing, scratched, broken glass, bent, b ad finish)
Comments __________________________________________________________________________

FIXTURE ASSEMBL Y INSTRUCTIONS

Read and review installation instruction sheet
before assembling the fixture

1. Place Glass Shade (K) over the socket to
sit onto the glass holder.

2. Insert Candle Sleeve (L) onto the so cket
and gently thread the sleeve onto the
socket to hold Glass Shade (K) into place.

3. Install the bulbs as per the fixtures
specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INST ALL THE SHADE ASSEMBLY AFTER THE

FIXTURE IS HUNG.

㎜ 1ea

2ea

Wall Anchors
2ea

1648-BA3 PARTS ASSEMBLY SHEET

F For Customer S ervice, contact Toll Free: 800.277.0979 Ext. 0 or Email: serv [e-mail]

INSTALLATION IN STRUCTIONS

Fixture Name: Olympia 1648-BA3 BUS

For Pendant Light Fixture

HANGING THE FIXTURE (Fig.1)

Fig. 1

Fig.2

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fig.3

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

1. Carefully remove the new fixture from the carton along
with the yellow bag that holds all of the parts. Check that all
parts are included as shown in the illustration and the Parts
and Assembly Sheet.

2. Shut off the power at the circuit breaker and completely
remove the old fixture from the wall, including the old
mounting strap.

3. Place Mounting Strap (B) over the Junction Box.

4. Attach Mounting Strap (B) to the Junction Box using
Mounting Screws (A). Tighten the screws securely using a
screw driver.

CONNECTING THE WIRES (Fig.2)

5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE ( or RIBBED) .

Ground wire connection: Connect the fixture ground

6.

wire to house ground wire, which usually has green or
copper insulation, with the correct size of wire
connector. If there is no house ground wire at ceiling
junction box then attach fixture ground wire securely
onto green grounding screw located on the mounting
bar.

NOTE: Twist the wires together in the same direction that you

twisted the wire connector onto the wires.

7. Tuck the wire connections neatly into the Junction Box.

FINISHING THE INSTALLATION (Fig.3)

8. Raise the fixture to the wall so that it covers the Junction
Box.

9. Align the holes at both sides of Mounting Strap (B) with the
holes in the Backplate. Secure the Backplate to the
Junction Box using Mounting Screws (I) and a screw driver.

10. Install the light bulbs and glass shade as per the Parts and
Assembly Sheet.

1648-BA3 INSTALLATION INSTRUCTION