Golden Lighting 1648-1W BUS User Manual
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet before
NOTE: I
Company Name:_______________________Co. Account #:_____________
below to be filled out by retaile r
PARTS & ASSEMBLY SHEET
Fixture Name: Olympia 1648- 1W BUS
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Mounting strap Mounting Screw Mounting screw
1ea 4" 2ea 8/32"X28mm 2ea 8/32X1"
Wire connnector Hex Nut Deco nut
3ea P4 Orange 2ea 8/32"X3.5mm 2ea @12mm
Green Ground
screw
1ea 8/32"X10mm
Part Needed Quantity
Part Needed Quantity
(round nut)
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
Fig. 4
1648-1W B US
Bulb
(Not Provided)
L
1. Slide the glass shade (K) and candle sleeves (L) over
the socket of fixture body (M).
2. Carefully press the clips inside of the shade (K) onto
the bulb.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of p urchase to arra nge for replacement parts.
J
K
H
M
INSTALLATION INSTRUCTIONS
Fig. 1
Fig. 2
11. Install glass as per the fixture assembly instructions
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
K
H
L
Fixture Name: Olympia 1648-1W BUS
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow
1. Carefully remove the new fixtur e from the carton and the
yellow bag that holes all your parts. Check that all parts are
bag that holes all your parts. Check that all parts are included as
included as shown in the illustration and parts list.
shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old fixture
2. Shut off power at the circuit br eaker and remove the old
from wall, including the old mounting strap.
fixture from wall, including the old mounting strap.
3. The Mounting Strap(A) contains several pairs of threaded holes,
find the pair of holes that match the holes spacing in your fixture
3. The Mounting Strap(A) contains several pairs of threaded
Back Plate (K) and thread the two Mounting Screws(B) half way
holes, find the pair of holes that match the holes spacing in y our
into the Mounting Strap(A).
fixture Back Plate (K) and thread the two Mounting Screws( B)
4. Place the Mounting Strap (A) over the Junction Box (E) so the
half way into the Mounting Strap(A).
Mounting Screws (B) are vertical or horizontal, as required by
4. Place the Mounting Strap ( A) over the Junction Box (E) so
fixture type.
the Mounting Screws (B) are vertical or horizontal, as required
5. Attach the Mounting Strap (A) to the Junction Box (E) by using
by fixture type.
the two mounting screws(D). Tighten the screws securly.
CONNECTING THE WIRES (Fig. 2)
5. Attach the Mounting Strap (A) to the Junction Box (E) by
using the two mounting screws(D). Tighten the screws securly .
5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
CONNECTING THE WIRES (Fig. 2)
5. Attach the power supply wires to the fixture lead wires by
WHITE (or RIBBED).
connecting BLACK to BLACK (or SMOOTH) and WHITE to
6. Attach the GROUND wire(GREEN or COPPER) from the
WHITE (or RIBBED).
Junction Box and the fixture Ground wire to the green Ground
6. Attach the GROUND wire(GREEN or COPPER) from the
Screw on the Mounting Bracket (A) or connect both wires
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (A) or connect both wires
together using the correct size of wire connectors.
together using the correct size of wire connectors.
NOTE:Twist the wires together in the same direction you twist the
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the w ires .
wire connector onto the wires.
7. Tuck these wire connections neatly into the Junction Box.
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig.3)
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate (J), over the Mounting
9. Place the fixture Back Plate (J), over the Mounting screws(B), so
screws(B), so they protrude through the holes in the Back Plate
(J).
they protrude through the holes in the Back Plate (J).
10. Thread the Deco Nuts (H) onto the Mounting Screws (B)
10. Thread the Deco Nuts (H) onto the Mounting Screws (B) and
and continue turning until the Back Plate (J) is snug against the
wall.
continue turning until the Back Plate (J) is snug against the wall.
11. Install glass as per the fixture assembly instructions
YOUR INSTA LLATION IS NOW COMPLETE . RETUR N
POWER TO THE JUNCTION BOX AND TE ST THE FIXTURE.
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER
TO THE JUNCTION BOX AND TEST THE FIXTURE.
Fig. 3
J
M
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...