Golden Lighting 1567-BA3 PC User Manual
Mounting
5/32"*H38mm
Deco Nut
5/32"xH9mm
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet before
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
PARTS & ASSEMBLY SHEET
below to be filled out by retailer
L
K
J
H
M
N
I
Fixture Name: Riverton 1567-BA3 PC
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Company Name:_______________________Co. Account #:_____________
PARTS LIST
Circular
Mounting Strap
1 ea Ø4"*1.5mm
Wire Connector
3 ea
P3
Green Ground
Screw
1 ea
#8-32N*H10mm
Part Needed Quantity
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
assembling the fixture.
1. Thread the Tube Finial to inside of Fixture
Tube (N).
Junction Box Screw
2 ea
#8-32N*H32mm
Hex Nut
2 ea
5/32"*H3.5mm
Tube Finial
2 ea
3/8"xH37mm
Screw
2 ea
(Round)
2 ea
1567-BA3 PC
Fig. 4
2. Place the fixture Back Plate ( K ), over the
Mounting Screws (B), so it protrude through the
hole in the Back Plate (K).
2. Thread the Deco Nuts (L) onto the Mounting
Screws (B) and continue turning until the
Back Plate (K) is snug against the wall .
3. Slide the Glass Shade (H) over Socket (I)
and secure Glass Shade (H) by threading the
Socket Ring (J) onto Socket (I) until tight.
4.Install light bulb to Socket (I) in accordance
with the fixture's specifications .
For Customer Service, contact the place of purchase to arrange for replacement parts.
1567-BA3PartsInstallation_20120502.xls
INSTALLATION INSTRUCTIONS
Fig. 2
4.Place the Mounting Strap (A) over the Junction Box (E) so
L
K
J
H
M
N
I
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
G C
D
E B A F
JUNCTION BOX
Fixture Name: Riverton 1567-BA3 PC
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1.Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.
3.The Mounting Strap (A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing in
your fixture Back Plate (K) and thread the two Mounting
Screws (B) half way into the Mounting Strap (A).
the Mounting Screws (B) are vertical or horiz ontal, as
required by fixture type.
5. Attach the Mounting Strap (A) to the Junct ion Box (E) by
using the two Junction Mounting Screws(D). Tighten the
screws securely.
CONNECTING THE WIRES ( F ig. 2)
6. Attach the power supply wires to t he fixture lead w ires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attached the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Strap (B) or
connect both wires together using the correct size
of wire connectors
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the unction Box.
Fig. 1
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate ( K ), over the Mounting
Screws (B), so it protrude through the hole in the Back Plate
( K ).
10. Thread the Deco Nuts ( L ) onto the Mounting
Screws (B) and continue turning until the Back Plate (K) is
snug against the wall .
11. Install light bulbs and glass shade as per the fixture
assembly instructions
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...