Golden Lighting 1567-BA2 PC User Manual
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Read and review installation instruction sheet before
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
K
J
I
H
L
M
N
Fixture Name: Riverton 1567-BA2 PC
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Circular
Mounting Strap
1 ea Ø4"*1.5mm
Wire Connector
3 ea
P3
Green Ground
Screw
1 ea
#8-32N*H10mm
Part Needed Quantity
Part Needed Quantity
Junction Box Screw
2 ea
#8-32N*H32mm
Hex Nut
2 ea
5/32"*H3.5mm
Tube Finial
2 ea
3/8"xH37mm
Mounting
Screw
2 ea
5/32"*H38mm
Deco Nut
(Round)
2 ea
5/32"xH9mm
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
Fig. 4
1. Thread the Tube Finial to inside of Fixture
Tube (N).
1567-BA2 PC
2. Place the fixture Back Plate ( K ), over the
Mounting Screws (B), so it protrude through the
hole in the Back Plate (K).
2. Thread the Deco Nuts (L) onto the Mounting
Screws (B) and continue turning until the
Back Plate (K) is snug against the wall .
3. Slide the Glass Shade (H) over Socket (I)
and secure Glass Shade (H) by threading the
Socket Ring (J) onto Socket (I) until tight.
4.Install light bulb to Socket (I) in accordance
with the fixture's specifications .
For Customer Service, contact the place of purchase to arrange for replacement parts.
1567-BA2PartsInstallation_20120502m.xls
INSTALLATION INSTRUCTIONS
Fig. 2
5. Attach the Mounting Strap (A) to t he Junc t ion Box (E) by
K
J
I
H
L
M
N
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
G C
D
E B A F
JUNCTION BOX
Fixture Name: Riverton 1567-BA2 PC
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE(Fig.1)
1.Carefully remove the new fixture from t he car ton and the
yellow bag that holds all your parts. Check that all
parts are included as shown in the illustration and parts list.
2. Shut off power at the circuit br eaker and remove the old
fixture from wall, including the old mounting strap.
3.The Mounting Strap (A) contains several pairs of
threaded holes, find the pair of holes that match the holes
spacing in your fixture Back Plate (K) and thr ead t he two
Mounting Screws (B) half way into the Mounting Strap (A).
4.Place the Mounting Strap (A) over the Junction Box (E)
so the Mounting Screws (B) are vertical or horizontal, as
required by fixture type.
using the two Junction Mounting Screws(D). Tighten t he
screws securely.
CONNECTING THE WIRES ( F ig. 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attached the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the gr een
Ground Screw on the Mounting Strap (B) or
connect both wires together using the cor rect size
of wire connectors
NOTE: Twist the wires together in the sam e dir ection you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the unction Box.
Fig. 1
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate ( K ), over the Mounting
Screws (B), so it protrude through the hole in the Back
Plate ( K ).
10. Thread the Deco Nuts ( L ) onto t he Mounting
Screws (B) and continue turning until the Back Plate (K) is
snug against the wall .
11. Install light bulbs and glass shade as per the fixture
assembly instructions
YOUR INSTALLATION IS NOW COMPLETE. RET URN
POW ER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...